crwdns2933423:0crwdne2933423:0

任天堂 Switch Lite 左操纵杆更换

crwdns2935443:0crwdne2935443:0

= crwdns2915112:0crwdne2915112:0 = crwdns2861241:0crwdne2861241:0
crwdns2936315:0crwdne2936315:0
crwdns2936311:0crwdne2936311:0
    Follow this guide to replace the left joystick in your Nintendo Switch Lite. Replacing the joystick will fix the notorious “Joy-Con drift” issue. (Follow [guide|137374|this guide to replace the right joystick in your Nintendo Switch Lite|new_window=true]).
    The Switch Lite uses JIS screws, but you can use a Phillips screwdriver in a pinch. Be very careful not to strip the screws. iFixit's Phillips bits are designed to be cross-compatible with JIS-style screws.
    After the repair, recommend to [link|https://www.ifixit.com/Troubleshooting/Joy-Con/Nintendo+Switch+Joy-Con+Drift/481780#Section_Joysticks_Need_Calibration|calibrate the replaced joystick|new_window=true] before playing any games.
    ***Note:*** This procedure requires disconnecting the battery for safety. In order to do this, the shield plate must be removed. The shield plate is bonded to the heat sink with thermal paste, which will need to be cleaned off and reapplied before reinstalling the shield plate.

      crwdns2931349:0crwdne2931349:0

      crwdns2936071:01crwdne2936071:0 — 移除左侧扬声器模块

      用镊子或手指将左扬声器电缆笔直向上拉出,并从子板上的插槽中拔出。

      crwdns2936071:02crwdne2936071:0

      用 JIS 000 螺丝刀或官方 iFixit PH 000 螺丝刀卸下固定左扬声器模块的4.5 mm 螺丝。

      crwdns2936071:03crwdne2936071:0

      用手指向上提起扬声器模块,将其从凹槽中取出以将其卸下。

      crwdns2936071:04crwdne2936071:0 — 断开主板

      使用打开工具或指甲将主板互连电缆的ZIF接口上的小铰链锁定翻盖向上翻转。

      crwdns2936071:05crwdne2936071:0

      用镊子将主板互连电缆从子板上的接口中滑出。

      crwdns2936071:06crwdne2936071:0 — 断开屏幕连接

      使用打开工具或指甲将两个带状电缆ZIF 接口上的小铰接锁定翻盖向上翻转。

      crwdns2936071:07crwdne2936071:0

      使用镊子将子板的屏幕电缆从其在主板上的接口中滑出。

      crwdns2936071:08crwdne2936071:0 — 移除音量键

      用镊子或手指卸下音量按钮。

      crwdns2936071:09crwdne2936071:0 — 断开操纵杆电缆

      使用打开工具或指甲翻转左操纵手柄电缆ZIF接口上的小铰链锁片。

      crwdns2936071:010crwdne2936071:0

      使用镊子将左操纵手柄电缆从子板上的接口中滑出。

      crwdns2936071:011crwdne2936071:0 — 移除图中左侧按钮

      用 JIS 000 螺丝刀或官方 iFixit PH 000 螺丝刀拆下固定左触发按钮总成的两个4.5 mm 螺丝。

      crwdns2936071:012crwdne2936071:0

      拆下左触发器按钮组件。

      crwdns2936071:013crwdne2936071:0 — 移除子板

      用 JIS 000 螺丝刀或官方 iFixit PH 000 螺丝刀拆下以下四个螺丝:

      crwdns2936071:014crwdne2936071:0

      用手指向上提起子板并将其从凹槽中取出。

      crwdns2936071:015crwdne2936071:0 — 移除左侧操纵杆

      用 JIS 000 螺丝刀或官方 iFixit PH 000 螺丝刀拆下固定左操纵杆的两个3.5 mm螺丝。

      crwdns2936071:016crwdne2936071:0

      使用定位铲的平端将操纵杆向上提离凹槽。

      crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0