crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Microsoft Surface Pro ディスプレイの交換

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:04crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:02crwdne2931653:0
Microsoft Surface Pro Display Replacement, Lift display and cut adhesive: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Microsoft Surface Pro Display Replacement, Lift display and cut adhesive: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Microsoft Surface Pro Display Replacement, Lift display and cut adhesive: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Lift display and cut adhesive

  • Apply a suction cup as close as possible to the edge of the display.

  • Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.

  • Slide the opening pick all the way around the edges of the display to cut through the adhesive on the bezel.

  • Do not insert the opening pick past the bezel of the display—you may permanently damage the display.

  • The bezel is much thinner on the bottom of the display, which is the side with the Windows logo. To avoid damage, don't poke too deep with the opening pick on the bottom edge.

  • Ribbon cables and a circuit board are approx. 0.6 cm from the edge of the glass.

  • Be very careful and move slowly during this step. The display is fragile and will crack if too much force is applied against it. If your tools seem stuck, apply more heat to further soften the adhesive.

crwdns2935429:0crwdne2935429:0

吸盤をディスプレイ端の出来る限り近い位置に装着して下さい。

ディスプレイの端に開口ピックが入る程度の隙間を作り、吸盤を差し込んでディスプレイを持ち上げます。

開口ピックをディスプレイ端から反対側までスライドさせて、ベゼルとの接着剤を切ります。

開口ピックはディスプレイのベゼル部分以上奥に差し込まないで下さい。　ディスプレイに致命的な損傷を与えることになります。

この手順では作業に注意しながら、ゆっくりとスライドします。ディスプレイは壊れやすく、力を加えすぎるとすぐにひび割れが発生します。もし、ツールが動かなくなった場合、再び接着剤を温めて柔らかくしてください。

+[title] Lift display and cut adhesive
[* black] Apply a suction cup as close as possible to the edge of the display.
[* black] Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.
[* black] Slide the opening pick all the way around the edges of the display to cut through the adhesive on the bezel.
[* icon_caution] Do not insert the opening pick past the bezel of the display—you may permanently damage the display.
+ [* icon_caution] The bezel is much thinner on the bottom of the display, which is the side with the Windows logo. ***To avoid damage, don't poke too deep with the opening pick on the bottom edge***.
+ [* red] Ribbon cables and a circuit board are approx. 0.6 cm from the edge of the glass.
[* icon_caution] Be very careful and move slowly during this step. The display is fragile and will crack if too much force is applied against it. If your tools seem stuck, apply more heat to further soften the adhesive.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0