crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Procédure d'ouverture du Google Pixel 3 XL

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:012crwdnd2931529:0crwdne2931529:0

crwdns2935423:0crwdne2935423:0

crwdns2935425:01crwdne2935425:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936317:0crwdne2936317:0
crwdns2931653:01crwdne2931653:0
Google Pixel 3 XL Opening Procedure, Heat the edge of the back cover: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Google Pixel 3 XL Opening Procedure, Heat the edge of the back cover: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Google Pixel 3 XL Opening Procedure, Heat the edge of the back cover: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Heat the edge of the back cover

  • Heat an iOpener and apply it to the right edge of the back cover for a minute.

  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

  • While you wait, note the following areas on the back cover:

  • Strong adhesive—there are large patches of adhesive near the bottom of the phone.

  • Fingerprint sensor cable—be careful not to slice through the cable as you pry

Chauffer le bord du panneau arrière

Faites chauffer un iOpener et posez-le sur le bord droit du panneau arrière pendant une minute.

Vous pouvez aussi utiliser un sèche-cheveux, un pistolet à air chaud ou une plaque chauffant, mais faites attention à ne pas surchauffer le téléphone. L'écran et la batterie interne sont tous deux sensibles à la chaleur.

Pendant que vous attendez, repérez les zones suivantes de la coque arrière :

Il y a beaucoup d'adhésif tenace en bas du téléphone.

Faites attention à ne pas trancher la nappe du lecteur d'empreintes digitales en faisant levier.

-[title] Heat the edge of the back panel
-[* black] [guide|25705|Heat an iOpener|new_window=true] and apply it to the right edge of the back panel for a minute.
+[title] Heat the edge of the back cover
+[* black] [guide|25705|Heat an iOpener|new_window=true] and apply it to the right edge of the back cover for a minute.
[* icon_note] A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.
-[* black] While you wait, note the following areas on the back panel:
+[* black] While you wait, note the following areas on the back cover:
[* red] Strong adhesive—there are large patches of adhesive near the bottom of the phone.
[* orange] Fingerprint sensor cable—be careful not to slice through the cable as you pry

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0