crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Remplacement de l'écran LCD & vitre tactile du Huawei Honor 8

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936317:0crwdne2936317:0
crwdns2931653:07crwdne2931653:0
Huawei Honor 8 LCD & Digitizer Replacement: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Huawei Honor 8 LCD & Digitizer Replacement: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Huawei Honor 8 LCD & Digitizer Replacement: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

  • Once the screen is warm to the touch, apply a suction cup near the top edge of the phone right under the earpiece speaker.

  • If the phone's screen is cracked, the suction cup may not stick. Try lifting it with strong tape, or superglue the suction cup in place and allow it to cure so you can proceed.

  • Pull up the suction cup to create a gap between the screen and the display bezel.

  • Insert the tip of an opening pick in the gap you created and slide it to top right corner of the phone. Leave it there to prevent the adhesive from resealing.

Si l'écran de votre téléphone est fissuré, la ventouse risque de ne pas adhérer correctement. Essayez de soulever avec du ruban adhésif épais, ou bien collez la ventouse avec de la superglue que vous laissez sécher avant de continuer.

Pendant que vous coupez, assurez-vous que le médiator passe bien sous le panneau de l'écran et non entre l'écran et la vitre frontale.

Tirez sur la ventouse pour soulever le bord droit de l'écran et ouvrir un léger espace entre l'écran et le châssis.

Insérez un médiator dans l'espace que vous venez de créer et faites-le glisser vers le coin inférieur droit.

Évitez les attaches en plastique mentionnées ci-dessus.

-[* icon_note] If the phone's screen is cracked, the suction cup may not stick. Try [https://d3nevzfk7ii3be.cloudfront.net/igi/4MmKE22Cy2MavVZU|lifting it with strong tape|new_window=true], or superglue the suction cup in place and allow it to cure so you can proceed.
-[* icon_caution] While cutting, make sure the pick slides ***under the display panel ***and not just between the display and the front glass.
-[* black] Use the suction cup to pull up the right edge of the screen, opening a slight gap between the screen and the frame.
-[* black] Insert an opening pick in the gap you created and slide it to the bottom right corner.
- [* icon_note] Mind the plastic tabs mentioned before.
+[* black] Once the screen is warm to the touch, apply a suction cup near the top edge of the phone right under the earpiece speaker.
+ [* icon_note] If the phone's screen is cracked, the suction cup may not stick. Try [https://d3nevzfk7ii3be.cloudfront.net/igi/4MmKE22Cy2MavVZU|lifting it with strong tape|new_window=true], or superglue the suction cup in place and allow it to cure so you can proceed.
+[* black] Pull up the suction cup to create a gap between the screen and the display bezel.
+[* black] Insert the tip of an opening pick in the gap you created and slide it to top right corner of the phone. Leave it there to prevent the adhesive from resealing.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0