crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Nintendo Switch 후면 패널 교체하기

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:022crwdnd2931529:0crwdne2931529:0

crwdns2935419:0crwdne2935419:0
crwdns2936315:0crwdne2936315:0
crwdns2936325:0crwdne2936325:0
crwdns2931653:04crwdne2931653:0
Nintendo Switch Rear Panel Replacement, Remove the top and bottom screws: crwdns2935265:00crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Nintendo Switch Rear Panel Replacement, Remove the top and bottom screws: crwdns2935265:00crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
Remove the top and bottom screws

  • Use a JIS 00 driver to remove the following screws securing the rear panel:

  • One 2.5 mm-long screw on the top edge of the device

  • Two 2.5 mm-long screws on the bottom edge of the device

  • To prevent these tight screws from stripping, apply firm downward force, work slowly and try another JIS 00 driver if the screws won't come out. Make sure the driver is fully inserted.

  • You can use a Phillips #000 screwdriver in a pinch, but you risk damaging or stripping the screws. Push down firmly on the screwdriver and twist slowly. Often, switching drivers may help, even if they are the same size.

상단 및 하단 나사 풀기

JIS 000 드라이버 혹은 iFixit PH 000 드라이버를 사용하여 후면 패널을 고정하는 다음 나사들을 풀어주세요:

기기 상단 가장자리에 있는 2.5mm-길이 나사 한 개

기기 하단 가장자리에 있는 2.5mm-길이 나사 두 개

단단히 조여진 나사가 마모되는 걸 막기 위해서 아래로 단단히 누르고 천천히 돌리세요. 그래도 나사가 움직이지 않을 경우 다른 JIS 000 또는 PH 000 드라이버를 사용해 보세요.

[title] Remove the top and bottom screws
-[* black] Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the rear panel:
+[* black] Use a JIS 00 driver to remove the following screws securing the rear panel:
[* red] One 2.5 mm-long screw on the top edge of the device
[* orange] Two 2.5 mm-long screws on the bottom edge of the device
- [* icon_note] To prevent these tight screws from [guide|13213|stripping], apply firm downward force, work slowly and try another JIS 000 or PH 000 driver if the screws won't come out.
+ [* icon_note] To prevent these tight screws from [guide|13213|stripping], apply firm downward force, work slowly and try another JIS 00 driver if the screws won't come out. Make sure the driver is fully inserted.
+ [* icon_note] You can use a Phillips #000 screwdriver in a pinch, but you risk damaging or [guide|13213|stripping the screws]. Push down firmly on the screwdriver and twist slowly. Often, switching drivers may help, even if they are the same size.

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0