crwdns2933423:0crwdne2933423:0

iPhone X 下部スピーカーの交換

crwdns2931529:0crwdnd2931529:0crwdnd2931529:0crwdnd2931529:017crwdnd2931529:0crwdne2931529:0

crwdns2935425:011crwdne2935425:0

crwdns2936315:0crwdne2936315:0
crwdns2936323:0crwdne2936323:0
crwdns2931653:011crwdne2931653:0
iPhone X Lower Speaker Replacement, Replace the speaker gasket: crwdns2935265:00crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 iPhone X Lower Speaker Replacement, Replace the speaker gasket: crwdns2935265:00crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 iPhone X Lower Speaker Replacement, Replace the speaker gasket: crwdns2935265:00crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
Replace the speaker gasket
  • The speaker's gasket is not reusable. During reassembly, follow this step to replace the gasket.

  • Use tweezers to peel off and remove all the old gasket from the frame and speaker.

  • Use a microfiber cloth and isopropyl alcohol to clean all the gasket's adhesive residue from the frame and speaker.

  • Before installing the speaker gasket, find its proper orientation on the bottom of the speaker—the large cutout on the gasket should go around the speaker grille mesh.

  • Remove the larger, clear liner from the gasket and use tweezers to carefully put the gasket into place on the bottom of the speaker.

  • To avoid touching the exposed adhesive, only grip the gasket by the outer edges of the liner.

  • Use your fingers or a spudger to firmly press the gasket into place to secure it with the adhesive.

  • Remove the remaining liner and put the speaker into place, making sure the speaker connector doesn't get stuck underneath.

スピーカーの接着性ガスケットは再利用できません。組み立て直す際は、本手順に従ってガスケットを交換して下さい。

ピンセットを使って筐体とスピーカーの古いガスケットを剥がして取り除いて下さい。

マイクロファイバークロスとイソプロピルアルコールを使って、残っているガスケットの接着剤の残骸を筐体とスピーカーから清掃して下さい。

新しいスピーカーガスケットを取り付ける前に 、スピーカーの底面に取り付けつ際の正しい向きを確認して下さい。ガスケットの大きい方の穴スピーカーグリルメッシュの周囲になるのが正しい向きです。

ガスケットについている大きくて透明な剥離紙を剥がしてから、ピンセットを使って慎重にガスケットをスピーカー底面の所定の位置に載せます。

剥き出しになっている接着剤に触れるのを避けるため、ガスケットを掴む際は剥離紙の外側の端だけを持つようにして下さい。

指やスパッジャーを使ってガスケットを所定の位置にしっかり押し付けて、ガスケットをしっかり貼り付けます。

残っている剥離紙を剥がしてからスピーカーを所定の位置に取り付けます。この際にスピーカーコネクタを裏側に閉じ込めないようにして下さい。

crwdns2944171:0crwdnd2944171:0crwdnd2944171:0crwdnd2944171:0crwdne2944171:0