crwdns2894164:0crwdne2894164:0

crwdns2890822:0crwdne2890822:0

crwdns2890844:0crwdne2890844:0

crwdns2861143:0crwdne2861143:0

crwdns2892376:0crwdne2892376:0

If the side brush on your Roomba 880 isn't spinning, it may need a new side brush motor. Here's how to replace it!

crwdns2860947:0crwdne2860947:0

crwdns2890040:0crwdne2890040:0

  1. Remove the two Phillips #1 15mm screws holding the battery cover in place. Once unscrewed, remove the battery cover and set aside. Once unscrewed, remove the battery cover and set aside.
    • Remove the two Phillips #1 15mm screws holding the battery cover in place.

    • Once unscrewed, remove the battery cover and set aside.

  2. Remove two 15mm Phillips #1 screws beneath each side wheel. Remove two 15mm Phillips #1 screws beneath each side wheel. Remove two 15mm Phillips #1 screws beneath each side wheel.
    • Remove two 15mm Phillips #1 screws beneath each side wheel.

  3. Remove the 10mm Phillips #1 screw holding the side brush in place. Once unscrewed, remove the side brush and set aside. Once unscrewed, remove the side brush and set aside.
    • Remove the 10mm Phillips #1 screw holding the side brush in place.

    • Once unscrewed, remove the side brush and set aside.

  4. Remove the outer covering.
    • Remove the outer covering.

  5. Remove the three 10mm Phillips #1 screws holding down the side brush motor case. Remove the three 10mm Phillips #1 screws holding down the side brush motor case.
    • Remove the three 10mm Phillips #1 screws holding down the side brush motor case.

  6. Take out the side brush motor case. Take out the side brush motor case.
    • Take out the side brush motor case.

  7. Remove the 10mm Phillips #1 screw holding down the lid of the side brush motor case.
    • Remove the 10mm Phillips #1 screw holding down the lid of the side brush motor case.

  8. Remove the piece holding the lid to the case. Take off the lid and set aside. Take off the lid and set aside.
    • Remove the piece holding the lid to the case.

    • Take off the lid and set aside.

  9. Remove the three 10mm Phillips #1 screws. Remove the three 10mm Phillips #1 screws.
    • Remove the three 10mm Phillips #1 screws.

  10. Flip over and remove the side brush motor. All done! All done!
    • Flip over and remove the side brush motor.

    • All done!

crwdns2892372:0crwdne2892372:0

To reassemble your device, follow these instructions in reverse order.

crwdns2878480:0crwdne2878480:0

agriewe

crwdns2886885:018/04/2017crwdne2886885:0

128 crwdns2894548:0crwdne2894548:0

crwdns2882065:0crwdne2882065:0

crwdns2892814:0crwdne2892814:0

Cal Poly, Team S17-G4, Banghart Spring 2017 crwdns2886886:0Cal Poly, Team S17-G4, Banghart Spring 2017crwdne2886886:0

CPSU-BANGHART-S17S17G4

crwdns2858115:05crwdne2858115:0

crwdns2886889:05crwdne2886889:0

crwdns2892924:00crwdne2892924:0

crwdns2892926:0crwdne2892926:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 2

crwdns2894768:07crwdne2894768:0 6

crwdns2894768:030crwdne2894768:0 27

crwdns2894770:0crwdne2894770:0 948