crwdns2894164:0crwdne2894164:0

crwdns2915892:0crwdne2915892:0

prereq only

  1. Use the flat end of a spudger to disconnect the rear-facing camera connector. Use the flat end of a spudger to disconnect the rear-facing camera connector.
    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

  2. Remove the following Phillips screws securing the rear camera bracket to the rear case: One 1.3 mm screw
    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

  3. Remove the bracket.
    • Remove the bracket.

  4. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.
    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

  5. Remove the two 1.2 mm tri-point screws securing the upper cable bracket.
    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

  6. Remove the upper cable bracket. Remove the upper cable bracket.
    • Remove the upper cable bracket.

  7. Use the flat end of a spudger to disconnect the upper cable connector. Use the flat end of a spudger to disconnect the upper cable connector.
    • Use the flat end of a spudger to disconnect the upper cable connector.

  8. Remove the four Phillips screws securing the Wi-Fi antenna: Three 1.2 mm screws
    • Remove the four Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

  9. Remove the top left antenna. Remove the top left antenna.
    • Remove the top left antenna.

  10. Remove the following Phillips screws:
    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

  11. Remove the bracket. Remove the bracket.
    • Remove the bracket.

    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using a standoff screwdriver or bit.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  12. Use tweezers to gently bend the logic board grounding bracket out of the way. Use tweezers to gently bend the logic board grounding bracket out of the way.
    • Use tweezers to gently bend the logic board grounding bracket out of the way.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

Evan Noronha

crwdns2886885:005/02/2015crwdne2886885:0

213 007 crwdns2915208:0crwdne2915208:0

crwdns2886889:0178crwdne2886889:0

crwdns2915084:0crwdne2915084:0

The Home Depot crwdns2886886:0The Home Depotcrwdne2886886:0

Community

crwdns2858115:08 894crwdne2858115:0

crwdns2886889:01 023crwdne2886889:0

crwdns2917036:00crwdne2917036:0

crwdns2917038:0crwdne2917038:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 1

crwdns2894768:07crwdne2894768:0 1

crwdns2894768:030crwdne2894768:0 1

crwdns2894770:0crwdne2894770:0 147