crwdns2936039:004 | Z and X Axis Assemblycrwdnd2936039:02crwdne2936039:0

crwdns2933803:02crwdne2933803:0

crwdns2933797:0Murathan Arazcrwdnd2933797:0N'w 2, 2018crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Murathan Araz

: crwdns2933769:0crwdne2933769:0
: crwdns2933771:0crwdne2933771:0
: crwdns2933801:0crwdne2933801:0

crwdns2933807:0crwdne2933807:0

+	[* orange] Insert 2 x[http://zaribo.org/hardware/12-linear-bushings-bearing-single-type-by-misumi.html\|LMU8 Bearings]. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] and [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x10 Socket Cap Screws] to tighten the bearings just to hold the bearings in their place. Attention! DO NOT TIGHTEN more!
+	[* green] Put the [http://zaribo.org/stepper-motors/38-original-prusa-mk2-mk3-pom-nut-zaribo-edition.html\|Pom Nut] and align the unthreaded holes for the screws. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Nuts] ''(See the small picture at left-bottom to insert one of the M3 Nuts)'' and 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x18 Socket Cap Screws] to fasten the Pom Nut in it's place.
+	[* yellow] Insert 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] from top and bottom to fasten rod spacers. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Washers] and [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x10 Socket Cap Screws] to tighten later in order to take up the excessive space between rods and the X axis holders.
+	[* red] Insert 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] to the belt tensioner.
+	[* blue] Push the [http://zaribo.org/other/62-2gt-6mm-wide-belt-timing-pulley-16t-toothless-2pc-set.html\|Idler Timing Pulley] inside the belt tensioner.
+	[* violet] Use the supplied [http://zaribo.org/home/112-dowel-pin.html\|Dowel Pin] to secure the Idler Pulley.
+	[* black] Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Washers] and 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x20 Socket Cap Screws] to mount the belt tensioner. Catch the M3 nuts in the tensioner, and tighten the M3 screws up to the celearance of the tensioner.

crwdns2933777:01crwdne2933777:0

crwdns2933779:0crwdne2933779:0

crwdns2915182:0crwdne2915182:0

crwdns2933777:02crwdne2933777:0

crwdns2933779:0crwdne2933779:0

crwdns2915182:0crwdne2915182:0

crwdns2933777:03crwdne2933777:0

crwdns2933779:0crwdne2933779:0

crwdns2915182:0crwdne2915182:0

+	[* orange] Insert 2 x[http://zaribo.org/hardware/12-linear-bushings-bearing-single-type-by-misumi.html\|LMU8 Bearings]. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] and [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x10 Socket Cap Screws] to tighten the bearings just to hold the bearings in their place. Attention! DO NOT TIGHTEN more!
+	[* green] Put the [http://zaribo.org/stepper-motors/38-original-prusa-mk2-mk3-pom-nut-zaribo-edition.html\|Pom Nut] and align the unthreaded holes for the screws. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Nuts] ''(See the small picture at left-bottom to insert one of the M3 Nuts)'' and 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x18 Socket Cap Screws] to fasten the Pom Nut in it's place.
+	[* yellow] Insert 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] from top and bottom to fasten rod spacers. Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Washers] and [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x10 Socket Cap Screws] to tighten later in order to take up the excessive space between rods and the X axis holders.
+	[* red] Insert 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|Nylon M3 Nuts] to the belt tensioner.
+	[* blue] Push the [http://zaribo.org/other/62-2gt-6mm-wide-belt-timing-pulley-16t-toothless-2pc-set.html\|Idler Timing Pulley] inside the belt tensioner.
+	[* violet] Use the supplied [http://zaribo.org/home/112-dowel-pin.html\|Dowel Pin] to secure the Idler Pulley.
+	[* black] Use 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3 Washers] and 2 x [http://zaribo.org/screws-nuts/67-zaribo-screw-kit.html\|M3x20 Socket Cap Screws] to mount the belt tensioner. Catch the M3 nuts in the tensioner, and tighten the M3 screws up to the celearance of the tensioner.