crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

crwdns2944351:0crwdnd2944351:0DeckLink HD Extreme 3D+ Fan Replacementcrwdnd2944351:0crwdne2944351:0

crwdns2933797:0Wolfgangcrwdnd2933797:0crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Wolfgang

crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933801:0crwdne2933801:0
crwdns2866306:0crwdne2866306:0
DeckLink HD Extreme 3Dplus Fan
Type
replacement
Thing
Fan
Title
DeckLink HD Extreme 3D+ Fan Replacement
Introduction
Thanks for cechking on this short guide how I solved and replaced the super noisy fan of the quite old DeckLink HD Extreme 3D+ Card from Blackmagic.
I wantet to find a solution without soldering, and here it is.
Took me about a week until I had everything together that I needed. Time for research not included.
I am sure one could to this much nicer. But I don’t look at it all the time so I don’t mind if there is a lot cable around or the fan does not sit perfectly aligned. So be sure to be as precise as you like and see this more as a inspiration.
You will need quite a few things:
* Replacement Fan which is silent of course!
* Maybe a small fan grill to add to the top.
* New screws (M2)
* 3Pin 1.5 ZH 1,5mm Mini Micro JST
* Isolation tape.
=== Fan ===
***Technical data of my replacment fan:***
Size 40 mm
Thickness 10 mm
Mounting hole spacing 32,5 mm
Rotational speed 4500 RPM+/- 10%
Airflow 8,26 m3/h
Noise 14,9 dB (A
Bearing FDB (Fluid Dynamic Bearing) Cable length 30 cm Connector 3Pin
Power 6,5~12V DC / 0,02A ~ 0,05A / 0,13W ~ 0,6W
***Original fan:***
COFAN F-4008L 12B
DC12V 0.10A
=== JST ===
The JST is the small white connector. On the board is a 3Pin 1.5 ZH 1,5mm Mini Micro JST. I bought some after i measured aproximatley and they did fit.
=== M2 screws ===
I went to a local shop to get the right size for the fan. But it is definatly a M2 because the fan is screwed to the cooler underneath. In my case I took 2cm screw length but 16mm would have been enough.
Just do an online search where to buy this stuff.
Have fun!
Time Required Min
crwdns2931275:0crwdne2931275:0
Time Required Max
crwdns2931275:0crwdne2931275:0
Imageid
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
Difficulty
Moderate
Conclusion
To reassemble your device, follow these instructions in reverse order.
Author
Wolfgang
Public
crwdns2853046:0crwdne2853046:0

crwdns2935255:0crwdne2935255:0

  • In Progress added.
  • Community-Contributed Guide added.

crwdns2933623:0crwdne2933623:0

crwdns2933815:01crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302962 stepid 302962
crwdns2933815:02crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302965 stepid 302965
crwdns2933815:03crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302963 stepid 302963
crwdns2933815:04crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302964 stepid 302964
crwdns2933815:05crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302966 stepid 302966
crwdns2933815:06crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
stepid 302967 stepid 302967