crwdns2933423:0crwdne2933423:0

crwdns2944351:0crwdnd2944351:0Xiaomi Redmi Note 10 Pro Screen Replacementcrwdnd2944351:0crwdne2944351:0

crwdns2933797:0Adriana Zwinkcrwdnd2933797:0crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Adriana Zwink

crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933801:0crwdne2933801:0
crwdns2866306:0crwdne2866306:0
Xiaomi Redmi Note 10 Pro
Type
replacement
Thing
Screen
Title
Xiaomi Redmi Note 10 Pro Screen Replacement
Introduction
Use this guide to remove or replace the screen on your Xiaomi Redmi Note 10 Pro.
If the frame is deformed, it's important to replace it to make sure the new screen will mount correctly and won’t suffer damage from uneven pressure.
Due to the device’s design, you must remove the lithium-ion battery to access the display cables. If the battery was deformed during removal replace it with a new one—reusing a deformed battery is a potential safety hazard.
Before disassembling your device, ***discharge the battery below 25%***. The battery can catch fire and/or explode if accidentally punctured, but the chances of that happening are much lower if discharged.
***Note:*** This guide instructs you to replace only the screen while leaving the original frame and motherboard in place. However, some replacement screens for this phone come pre-installed in a new frame (a.k.a. chassis), which requires a very different procedure. Make sure you have the correct part before starting this guide.
Before you begin this procedure, be sure to have a set of replacement adhesives for both the back panel and the screen.
Time Required Min
crwdns2931289:01crwdne2931289:0
Time Required Max
crwdns2931291:02crwdne2931291:0
Imageid
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
Difficulty
Moderate
Conclusion
If possible, turn on your device and test your repair before installing new adhesive and resealing.
Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
***To reassemble your device, follow the above steps in reverse order.***
The best way to secure the new screen is to apply a sheet of custom-cut double-sided tape to the back of the screen.
Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers|new_window=true|Answers community] for help.
Author
Public
crwdns2853046:0crwdne2853046:0

crwdns2933809:0crwdne2933809:0

crwdns2943215:0crwdne2943215:0

  • SIM Card Eject Tool x1 added.
  • iOpener x1 added.
  • iFixit Opening Picks (Set of 6) x1 added.
  • Suction Handle x1 added.
  • Isopropyl Alcohol x1 added.
  • Heat Gun x1 added.
  • Spudger x1 added.

crwdns2943213:0crwdne2943213:0

  • iFixit Adhesive Remover x1 added.
  • Tesa 61395 Tape x1 added.

crwdns2935255:0crwdne2935255:0

  • In Progress added.
  • Featured Guide added.

crwdns2933623:0crwdne2933623:0

crwdns2933815:01crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0