crwdns2933423:0crwdne2933423:0

crwdns2944351:0crwdnd2944351:0Fix False Paper Jam Error.crwdnd2944351:0crwdne2944351:0

crwdns2933797:0Robert Backhauscrwdnd2933797:0crwdne2933797:0

crwdns2936043:0crwdne2936043:0 crwdns2933505:0crwdne2933505:0 Robert Backhaus

crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933801:0crwdne2933801:0
crwdns2866306:0crwdne2866306:0
HP Officejet Pro 8630
Type
replacement
Thing
Paper Jam Error Caused By Cleaning Station return spring
Title
Fix False Paper Jam Error.
Introduction
There are many things that can cause a paper jam error. First you must make sure that there is no debris stuck anywhere. If you have done this and there is still a paper jam, you could have this issue.
The symptoms of this fault are:
# The printer displays a 'Paper Jam' error, and tells you to remove the rear duplexer, and says that you may need to open the front cover too. When you touch 'OK', nothing happens, unless you open and close the front door.
# When you open and close the front door and then touch 'OK', the printer mechanism moves a little and then it displays the error again. Occasionally the printer may move through most of a full initialization before stopping again.
# If you bypass the door close mechanism (place an opaque object in the rectangular slot on the left hand side), you will see that the paper feed rollers are moving a small distance back, the carriage moves to the left slightly, then the feed rollers move forward and stop.
# Shine a light into the printer, and check over on the far left for a small lever. This lever should slide to the right with gentle pressure, and spring back into position. If it doesn't slide back, try pulling it gently to the left. If you can move the lever back and forth but it doesn't spring, then you need to disassemble your printer and replace this spring.
Time Required Min
crwdns2931287:030crwdne2931287:0
Time Required Max
crwdns2931287:030crwdne2931287:0
Imageid
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
Difficulty
Moderate
Conclusion
Proceed to reassemble your printer, working back through the instructions in the reverse order. You can test your repair as soon as you have restored the carriage support, and reconnected the cables connecting the front panel switches and control panel.
Author
Public
crwdns2853046:0crwdne2853046:0

crwdns2933809:0crwdne2933809:0

crwdns2943215:0crwdne2943215:0

  • TR10 Torx Security Screwdriver x1 added.
  • Spudger x1 added.
  • iSesamo Opening Tool x1 added.
  • Nitrile Gloves 100 Box x1 added.

crwdns2943213:0crwdne2943213:0

  • Generic spring, about 37mmx12mm, .65mm wire. x1 added.

crwdns2935255:0crwdne2935255:0

  • In Progress added.
  • Community-Contributed Guide added.

crwdns2933623:0crwdne2933623:0

crwdns2933815:01crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:02crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:03crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:04crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0
crwdns2933815:05crwdne2933815:0
crwdns2933769:0crwdne2933769:0
crwdns2933771:0crwdne2933771:0