crwdns2915892:0crwdne2915892:0
Through normal wear and tear or rough handling, saxophone corks can become damaged, rendering the instrument useless or operating at diminished quality. This guide will replace a Yamaha YAS-23 alto saxophone cork; however, the size for all alto saxophone neck-pieces is standard, so this repair is applicable to all alto saxophone neck-piece cork repairs.
For optimal performance, saxophones require a well fitting cork. Without this, tone quality will be sacrificed, or the saxophone will cease to function.
crwdns2942213:0crwdne2942213:0
-
-
Locate the screw on the side of the neck-piece, connecting the octave key to the neck-piece.
-
Use a small, 2.5 mm flat head screwdriver to remove the screw.
-
-
-
Open a paperclip.
-
Push the screw out with the end of the paperclip.
-
-
-
Slide the octave key down off the bottom of the neck-piece.
-
-
-
Use the utility blade to scrape off the cork.
-
Start at the base of the cork on the neck-piece with the utility blade at a 10 to 20 degree angle.
-
In a controlled motion, drag the utility blade along the neck-piece, removing cork along the way.
-
Repeat until all of the cork is removed.
-
-
-
Apply masking tape where there is no glue on the neck-piece to prevent damage to the finish.
-
-
-
Remove glue and resin by rotating the neck-piece against the 220 grit sand paper.
-
Repeat until all glue is gone.
-
-
-
crwdns2935267:0crwdne2935267:0Microfiber Cleaning Cloths$3.99
-
With a damp microfiber cleaning cloth, wipe off any dust and glue particles.
-
-
-
Place the Valentino neck cork flush with the entrance of the neck-piece.
-
Mark a line where the Valentino neck cork meets the masking tape.
-
Cut along the line.
-
-
-
Wrap Valentino neck cork around the neck-piece.
-
Make mark where the Valentino neck cork overlaps.
-
-
-
Cut the Valentino neck cork along the line made in the previous step.
-
-
-
Remove the adhesive covering on the back of the Valentino neck cork.
-
Wrap the Valentino neck cork around the top of neck-piece.
-
-
-
Sand the seam of the Valentino neck cork until it is even with the rest of the Valentino neck cork.
-
-
-
Apply a generous amount of cork grease on the whole Valentino neck cork.
-
-
-
Place the octave key on the neck-piece.
-
-
-
Re-insert the screw.
-
Tighten the screw with a small, 2.5 mm flat head screwdriver.
-
The replacement is complete.
-
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
University of North Texas, Team S1-G6, Raign Spring 2020 crwdns2935289:0University of North Texas, Team S1-G6, Raign Spring 2020crwdne2935289:0
UNT-RAIGN-S20S1G6
crwdns2931471:02crwdne2931471:0
crwdns2935303:01crwdne2935303:0
crwdns2947410:01crwdne2947410:0
I’m usually here for computer guides, I couldn’t believe a sax guide was here! Was overjoyed! Can someone make a Alto Sax full pad replacement guide? I know it’s a big ask! But I have a YAS-23 and it needs all new pads, getting it serviced by a pro is between $700-$850!! But buying pads yourself is as low as $50 or on the high end $200. This seems like a tutorial the world needs to have! Thank you to anyone that even took the time to read this.
