XtremeMac Luna Button Circuit Boards Replacement

crwdns2931653:01crwdne2931653:0 Bottom Panel




• Flip the device over so that the batteries are closest to you.
• Remove the battery lid by pressing the battery cover's tab and pulling it away from the device.
• Push the battery against the spring and lift it out of the casing.
• Repeat with the other battery.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0

• Unscrew all eight 12mm Phillips head screws with a Philips #1 screwdriver.
• The iFixit 26 bit screwdriver kit will not reach the screws. Make sure to use a screwdriver that is thin enough to not get stuck in the screw holes.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Flip the Luna back over so that the buttons are facing upward and the LCD screen is facing you.
• Gently tilt the lid back 45 degrees so that the inside is exposed.
• Be mindful of the wires inside of the Luna. It is easy to break a connection if a wire gets caught.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0 Dock Circuit Board
• Unscrew the four black 7mm screws with the Phillips #1 screw driver that hold the middle circuit board to the top case.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0 Button Circuit Boards
• Unscrew the three 7 mm black screws using the Philips #1 screwdriver on the back end of the left and right circuit board.
• Removing the right circuit board first will make it easier to unscrew the left because the heat-sinks on the left circuit board can get in the way of the screwdriver.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Use a plastic opening tool to pry the black connections away from the top casing.
• Be attentive when you separate the circuit boards from the top, as there is a loose wheel inside.
crwdns2913378:0crwdne2913378:0
crwdns2935261:0crwdne2935261:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Turn the circuit boards over. Remove the two connections on the left side by pulling on the tabs.
• The glue that holds the connection together will come off when you pull. Pull on the tab with enough force to break the glue without damaging the wires.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:04crwdnd2935293:0crwdne2935293:0

Andre Rivera

crwdns2935283:004/17/13crwdne2935283:0

8 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 5

• 
• 
• 

crwdns2935301:02crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 3-47, Amido Spring 2013 crwdns2935289:0Cal Poly, Team 3-47, Amido Spring 2013crwdne2935289:0

CPSU-AMIDO-S13S3G47

crwdns2931471:04crwdne2931471:0

crwdns2935297:08crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0