Vtech Kidizoom Smart Watch DX Circuit Board Replacement

crwdns2931653:01crwdne2931653:0 Master Switch

• Make sure the master switch is "OFF" before disassembly, to avoid an electric shock.
• Flip the watch over with the back facing up.
crwdns2913378:0crwdne2913378:0
crwdns2947430:01crwdne2947430:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0

• Remove the four 6.0 mm screws on the back plate with the Phillips #00 screwdriver.
crwdns2913378:0crwdne2913378:0
crwdns2947430:01crwdne2947430:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Gently pull the back plate from the watch casing.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Lift the master switch from the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2935263:02crwdne2935263:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0 Circuit Board
• The speaker wires are fragile. They may break if excessive force is used to remove the circuit board.
• Removal of the circuit board requires soldering.
• Gently push on the display from the front, near the camera. The circuit board and display will pop out through the back.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Lift the circuit board carefully from the casing, without breaking or detaching the speaker wires at the bottom of the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Note which wire is connected to which lead before continuing. There are no markers on the circuit board to indicate where each wire belongs.
• De-solder the black speaker wire from the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:08crwdne2931653:0
• De-solder the red speaker wire, as in the previous step.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:09crwdne2931653:0
• Wait for the solder to cool down and solidify, then remove the circuit board from the casing.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

Jordan RiberSmith

crwdns2935283:001/20/16crwdne2935283:0

755 crwdns2915208:0crwdne2915208:0

crwdns2935297:02crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 11

• 
• 
• 

crwdns2935301:08crwdne2935301:0

crwdns2915084:0crwdne2915084:0

USF Tampa, Team 10-6, Remmell Spring 2016 crwdns2935289:0USF Tampa, Team 10-6, Remmell Spring 2016crwdne2935289:0

USFT-REMMELL-S16S10G6

crwdns2931471:04crwdne2931471:0

crwdns2935297:012crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0