crwdns2915892:0crwdne2915892:0
You will need to use a source of heat. You may need to buy adhesive for the reassembly. Make sure the phone is completely powered off before opening the device.
crwdns2942213:0crwdne2942213:0
-
-
Apply heat on the back surface of the phone.
-
-
-
Stick the small suction cup on the bottom half of the back surface of the phone.
-
-
-
With the bottom of the device facing you, lift up on the suction cup handle.
-
Use the plastic opening tool around all sides to pry off the back cover.
-
-
-
Pull the back of the phone case away from the device.
-
-
-
Apply heat to the copper RAF antenna.
-
-
-
Peel back the black tabs on the battery.
-
-
-
Use a plastic opening tool to pry up the orange battery connector that is directly above the battery in the center of the phone.
-
-
-
Use a plastic opening tool to get under the battery and pry it up.
-
-
-
Lift the battery out with your hands.
-
-
-
Remove the four 4mm screws holding the loudspeaker in place with a Phillips #00 screwdriver.
-
-
-
-
Push back the two retaining tabs on the top of the loudspeaker with the spudger.
-
-
-
Pry the loudspeaker up with the spudger.
-
-
-
Remove the loudspeaker with your hands.
-
-
-
With a spudger, pry up the orange connector that is directly underneath where the loud speaker was just removed.
-
-
-
Pry up the small silver connector on the right side of the bottom of the phone with a spudger.
-
-
-
Pry up the charging port using a spudger.
-
-
-
Remove the five black 4mm screws with a Phillips #00 screwdriver.
-
-
-
Pry up the black camera case with a nylon spudger, and then remove the case.
-
-
-
Use a spudger to pry up the six motherboard connectors.
-
-
-
Use the flat end of the nylon spudger to lift the camera out of the phone.
-
-
-
Pull out the front camera using your fingers.
-
-
-
Use the spudger to separate the motherboard from the frame.
-
-
-
Pry up the headphone jack using a spudger.
-
-
-
Peel back the black tabs that were holding the battery in place.
-
-
-
Remove the two 4 mm screws with a Phillips #000 screwdriver from the left side of the back of the screen.
-
-
-
Remove the three 3mm screws with a T5 screwdriver along the side of the device where the volume buttons are.
-
-
-
Push down the side of the screen that you just removed screws from.
-
-
-
Pull up the orange and black tab that is on the left half of the middle of the screen.
-
-
-
Remove the three 3 mm screws with a Star Bit T5 Screwdriver on the opposite side of the phone.
-
-
-
Use tweezers to remove the earpiece.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:07crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team S17-G2, Livingston Spring 2018 crwdns2935289:0Cal Poly, Team S17-G2, Livingston Spring 2018crwdne2935289:0
CPSU-LIVINGSTON-S18S17G2
crwdns2931471:04crwdne2931471:0
crwdns2935297:08crwdne2935297:0
