Sony Cyber-Shot DSC-S90 LCD Display Replacement
crwdns2944107:0crwdnd2944107:0Jonathan Arnscrwdnd2944107:0crwdnd2944107:0crwdnd2944107:03crwdnd2944107:0crwdne2944107:0
crwdns2944111:0Sun 25, 2021crwdne2944111:0
crwdns2915892:0crwdne2915892:0
crwdns2942287:0crwdne2942287:0When removing the Sony Cyber-Shot DSC-S90 LCD display, it’s important to know when replacing or dissembling the overall display, it is one of the few processes that required disassembly of the majority of the camera. You will need a total of two tools consisting of the plastic opening tool, and the J00 screwdriver. This is a moderately difficult step, but may take more time than anticipated.
crwdns2942213:0crwdne2942213:0
crwdns2943215:0crwdne2943215:0
crwdns2944105:0crwdne2944105:0
-
-
Hold down the "open"button (gray oval with arrow pointing upwards) on the battery port door.
-
While holding the button downwards, slide the door upwards to unlock and open the door.
-
-
-
Pull open the door and allow the batteries to fall out.
-
-
-
Remove the 2mm Phillips #00 screw under the battery port door.
-
Remove the 2mm Phillips #00 screw towards the right of the bottom-side of the camera.
-
-
-
Remove the two 2mm Phillips #00 screws (one on each side of the camera).
-
-
-
Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the right side and bottom of the camera with the LCD screen facing you.
-
-
-
Pull apart the back case from the main body of the camera.
-
-
-
Use an opening tool to unlock the front case from the main body of the camera. Use the tool on the top of the camera.
-
-
-
-
Pull apart the front case from the main body of the camera.
-
-
-
Release all clips and latches keeping the casing in place using a spudger, opening tool, or screwdriver.
-
-
-
Now the casing can be removed after all latches have been undone.
-
-
-
Disconnect the ribbon cables on top of the battery terminal using a spudger or screwdriver.
-
-
-
Disconnect the remaining ribbon cable on the side of the camera using a spudger or screwdriver.
-
-
-
Use a spudger or screwdriver to unhinge the clips. This releases the battery terminal.
-
-
-
Once the battery terminal is unclipped, pull this ribbon cable out with a spudger or screwdriver to finish freeing the battery terminal.
-
-
-
Now the battery terminal can be separated from the main body of the camera.
-
-
-
Disconnect the three pictured ribbon cables using a spudger or screwdriver.
-
-
-
Push the clip to the left and lift the motherboard upwards and away from the camera.
-
-
-
Disconnect the two ribbon cables using a spudger or screwdriver.
-
-
-
Unlatch the clip and lift the motherboard upwards and away from the camera.
-
-
-
Unlatch the two clips holding the LCD display onto the main camera housing using a spudger.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2915084:0crwdne2915084:0
UMass Dartmouth, Team S4-G5, Saloman Fall 2019 crwdns2935289:0UMass Dartmouth, Team S4-G5, Saloman Fall 2019crwdne2935289:0
UMASSD-SALOMAN-F19S4G5
crwdns2931471:03crwdne2931471:0
crwdns2935297:020crwdne2935297:0
