crwdns2942213:0crwdne2942213:0
- 
   
   - 
                     
            Remove battery and card 
 
- 
                     
            
- 
   
   - 
                     
            Right side, remove 1 M1.4x3.7 screw 
- 
                     
            Left side, remove 3 M1.4x3.7 screws 
- 
                     
            Bottom side, remove 5 M1.4x3.7 screws, including 2 in battery bay. 2 of them out of this photo, you can find them. 
 
- 
                     
            
- 
   
   - 
                     
            Pop the flash. 
- 
                     
            In flash room, remove 1 (one) M1.4x3.8 black screw. 
 
- 
                     
            
- 
   
   - 
                     
            Remove LCD hinge cover, by sliding to the left. 
- 
                     
            Remove back cover, actually just a plastic frame. 
 
- 
                     
            
- 
   
   - 
                     
            Remove 1 M1.4x2 screw 
- 
                     
            Remove another M1.4x2 screw, sorry for the angle. 
 
- 
                     
            
- 
   
   - 
                     
            Loosen LCD assemble with caution! 
- 
                     
            Release FPC cable, the connector is flip type. 
 
- 
                     
            
- 
                     
                                                
- 
   
   - 
                     
            After unscrew 4pcs screw you will remove the steel black plate, then slowly pull the black frame there to see the ribbon stripe. 
- 
                     
            Slowly pull the very fragile ribbon lock which i marking with the blue boxes. around just 1mm to unlock the ribbon.. unlucky i broke mine.. 
 
- 
                     
            
- 
   
   - 
                     
            you can see the ribbon already pull out but be carefull with the others 2 ribbon when your try to pull out this ribbon. 
- 
                     
            the the circle marker that show others ribbon you need to be carefull. goodluck! 
 
- 
                     
            
- 
   
   - 
                     
            Remove 1 M1.4x2 screw 
- 
                     
            Lift the keypad. 
- 
                     
            Detach FPC 
 
- 
                     
            
- 
   
   - 
                     
            Remove 3 M1.4x3.6 black screws, 2 of them out of focus 
 
- 
                     
            
- 
   
   - 
                     
            Slide the flash assembly backwards with caution. 
- 
                     
            Detach flash FPC by pulling it out of the socket. 
- 
                     
            Then remove the flash assembly. 
 
- 
                     
            
- 
   
   - 
                     
            Remove that part whatever called, by sliding it backwards. 
 
- 
                     
            
- 
   
   - 
                     
            1 ST1.7x5 
- 
                     
            2 ST1.7x5 
- 
                     
            1 M1.4x3.6 black 
 
- 
                     
            
- 
   
   - 
                     
            Remove 2 ST1.7x5 screws from inside the battery bay. (one of them not shown, deeper inside) insert screw driver through a hole in the shielding cover. 
- 
                     
            Pop the grip off. From back, push to the right, then it flies forward. 
 
- 
                     
            
- 
   
   - 
                     
            Remove 2 M1.4x2 black screws 
 
- 
                     
            
- 
   
   - 
                     
            with caution and patient. 
 
- 
                     
            
- 
   
   - 
                     
            Sensor power, flip 
- 
                     
            Sensor signal, flip 
- 
                     
            Shutter, pull 
- 
                     
            Lens contacts, pull. Did I mention that Sony makes world's most brittle FPC? 
- 
                     
            Whatever, pull 
- 
                     
            Whatever, pull 
- 
                     
            Shutter charger motor FPC, (backside, pull out) 
 
- 
                     
            
- 
   
   - 
                     
            Flip the Mainboard up 
- 
                     
            Pull out one more FPC 
- 
                     
            Discharge then desolder 4 wires. 
 
- 
                     
            
- 
   
   - 
                     
            Lift main board and plastic frame with flash capacitor. 
 
- 
                     
            
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
