crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Sega Genesis 6 button controller

crwdns2915892:0crwdne2915892:0

This guide will help you disassemble your Sega Genesis II 6 button controller. You will need a Phillips #00 screwdriver to complete this guide.

This specific model was released in 1992/93, at the same time as the Sega Genesis II. However, it is also compatible with the Sega Genesis I

crwdns2942213:0crwdne2942213:0

  1. Sega Genesis 6 button controller, Disassembling the handle: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Flip the controller upside down.

    • Using a Phillips #00 screwdriver, remove the five screws holding the controller back cover in place.

    crwdns2918738:0crwdne2918738:0

  2. Sega Genesis 6 button controller: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Then remove the back cover of the controller, which gives you access to the motherboard of the controller.

    • Carefully put back the 5 screws from step 1 as well as the back cover of the controller

    crwdns2918738:0crwdne2918738:0

  4. Sega Genesis 6 button controller, Disassembling the motherboard: crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Sega Genesis 6 button controller, Disassembling the motherboard: crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove the motherboard from the controller body, after releasing the rubber part that holds the cable in the controller body

    • This gives you access to the button contact pads

    crwdns2918738:0crwdne2918738:0

  5. Sega Genesis 6 button controller, Dismantling the buttons: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove the contact pads

    • Then remove the 8 plastic buttons

    crwdns2918738:0crwdne2918738:0

  6. Sega Genesis 6 button controller, Dismantling the Directional Pad: crwdns2935265:05crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 Sega Genesis 6 button controller, Dismantling the Directional Pad: crwdns2935265:05crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 Sega Genesis 6 button controller, Dismantling the Directional Pad: crwdns2935265:05crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

    • In order to disassemble the directional cross, it is necessary to levergentlypreferably with a plastic Spudger, under the 4 retaining tabs.

    • Then, push in the central hole with a fine tool (here a screwdriver), in order to undo the assembly

    • For reassembly, be careful to put the corrector in front of the slot of the outer part!

    crwdns2918738:0crwdne2918738:0
crwdns2915888:0crwdne2915888:0

Follow these steps in reverse order to reassemble your device.

crwdns2935227:0crwdne2935227:0

crwdns2934873:0crwdne2934873:0

fr en

100%

tayola

crwdns2934883:0tayolacrwdne2934883:0 crwdns2934875:0crwdne2934875:0
crwdns2934877:0crwdne2934877:0 ›

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

Thierry Benitez

crwdns2935283:001/14/19crwdne2935283:0

315 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 5

crwdns2935301:02crwdne2935301:0

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 6

crwdns2936753:030crwdne2936753:0 32

crwdns2942667:0crwdne2942667:0 994