crwdns2915892:0crwdne2915892:0
Replace the viewfinder located at the top of the camera.
crwdns2942213:0crwdne2942213:0
-
-
Push the rubber viewfinder grip upward.
-
-
-
Use the Phillips #00 screwdriver to remove one 6.4 mm screw in the center of the dial.
-
Remove the dial by lifting upward with your fingers.
-
-
-
Use the Phillips #00 screwdriver to remove the four 5.5 mm screws surrounding the viewfinder.
-
Use your fingers to lift the plastic viewfinder cover upward.
-
-
-
Use the Phillips #00 screwdriver to remove the two 5.5 mm screws from the right side of the camera above the SD card port.
-
-
-
Use the Phillips #00 screwdriver to remove one 5.5 mm screw on the left, above the HDMI port.
-
-
-
Use the Phillips #00 screwdriver to remove the five 5.5 mm screws from the bottom, near the battery compartment.
-
Use the Phillips #00 screwdriver to remove one 3.8 mm screw from the bottom of the hand grip, below the battery compartmen.
-
-
-
-
Use a plastic opening tool to separate the back cover from the front cover.
-
-
-
Use your fingers to pull the back cover away from the front cover.
-
-
-
Use tweezers to pull the two ribbon cables horizontally out of their clips.
-
-
-
Use the Phillips #00 screwdriver to remove the seven screws (three silver 3.5 mm screws and four black 2.7 mm screws).
-
-
-
Use tweezers to remove the glued rubber piece.
-
-
-
Use the Phillips #00 screwdriver to remove the four black 2.3 mm screws.
-
Use your fingers to separate the LCD screen from the folding mechanism.
-
-
-
Use tweezers to pull the five ribbon cables horizontally out of their clips.
-
Use a spudger or your fingernail to flip up the four, small retaining flap, or zero insertion force (ZIF) connectors. Then, pull the ribbon cable out to disconnect it.
-
Remove the green tape using your fingernail. Then, use a spudger to pry the one antenna cable connector straight up from the board.
-
Use tweezers or a spudger to pry up each side of the flat-topped connector. Then, lift the one connector straight up from its socket.
-
Use tweezers or your fingers to pull the two double-bundled cables up and away from the connector in the same direction that the individual wires are running.
-
-
-
Use the Phillips #00 screwdriver to remove the six silver 4.5 mm screws.
-
-
-
Use a spudger to lift the motherboard up starting on the right side proceeding to the left side.
-
Use your fingers to lift the motherboard completely out of the camera.
-
-
-
Use tweezers to lift the black tab on the ZIF connector.
-
Use tweezers to pull the large orange ribbon cable out of the connector to get a clearer view of the screws lying beneath it.
-
-
-
Use the Phillips #00 screwdriver to remove the three black 3.8 mm screws below the viewfinder.
-
-
-
Use a spudger to gently push the viewfinder cube, starting at the top of the cube and pushing it toward the bottom of the camera.
-
Use your fingers to lift the viewfinder cube out of the camera.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
USF Tampa, Team 1-4, Leahy Spring 2016 crwdns2935289:0USF Tampa, Team 1-4, Leahy Spring 2016crwdne2935289:0
USFT-LEAHY-S16S1G4
crwdns2931471:03crwdne2931471:0
crwdns2935297:06crwdne2935297:0
