crwdns2915892:0crwdne2915892:0
Is your camera exhibiting symptoms of a faulty motherboard? This guide will help you access the motherboard to replace it or make necessary repairs.
crwdns2942213:0crwdne2942213:0
-
-
Orient the camera so the button panel and LCD are facing you.
-
Use a spudger or fingernail to open the battery compartment on the right side of the camera.
-
-
-
Push the blue trapdoor to the left to release the battery, and remove the battery.
-
-
-
Use a Phillips #00 screwdriver to remove the 4 mm screw inside the battery compartment.
-
-
-
Remove the 4 mm Phillips #00 screw hiding in the external flash port.
-
-
-
Remove the four 5 mm Phillips #00 screws from the lens assembly.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Remove the metal lens mount by hand or with tweezers.
-
-
-
Use tweezers to remove the inner metal ring.
-
-
-
-
Use a Phillips #00 screwdriver to remove the three 4 mm screws from the bottom of the case.
-
-
-
Use your hands to slowly pull the front casing away from the camera.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Gently flip the sensor cover back to expose the screw attaching the sensor cover to the ribbon cable.
-
Use a Phillips #00 screwdriver to remove the 3 mm screw from the sensor cover.
-
Use tweezers to remove the metal contact cover. Be sure to carefully remove the cover so the gold contacts remain in place.
-
-
-
Remove the four 4 mm Phillips #00 screws holding the sensor mount in place.
-
-
-
Remove the four 4 mm Phillips #00 screws securing the battery compartment to the mother board.
-
Remove the battery compartment.
-
-
-
Use a spudger to disconnect the ribbon cable connecting the image sensor to the motherboard.
-
-
-
Gently remove the sensor mount from the camera case.
-
-
-
Use a Phillips #00 screwdriver to remove the 3 mm screw located below the wifi antenna.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Use tweezers to disconnect the wifi antenna from the motherboard.
-
-
-
Use a spudger to disconnect the LCD ribbon cable by prying it straight up from the motherboard.
-
-
-
Use a spudger to unlock the topmost ZIF connector by flipping open the black flap.
-
-
-
Insert the pointed end of a spudger into the hole in the middle of the ribbon cable.
-
Gently pull the spudger back to slide the ribbon cable out of its connector.
-
-
-
Disconnect the blue ribbon cable from the motherboard.
-
Insert the pointed end of a spudger into the hole in the top of the ribbon.
-
Gently pull the ribbon from the connector.
-
-
-
Remove the motherboard from the camera.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
iFixit, Team S1-G1, Weber Summer 2018 crwdns2935289:0iFixit, Team S1-G1, Weber Summer 2018crwdne2935289:0
FIX-WEBER-SU18S1G1
crwdns2931471:05crwdne2931471:0
crwdns2935297:043crwdne2935297:0
