crwdns2915892:0crwdne2915892:0
This repair guide will give you step by step instructions on how to remove the Macintosh PowerBook 1400c Monitor.
crwdns2942213:0crwdne2942213:0
-
-
Turn the device upside down and then locate the battery latch near the front of the device.
-
-
-
Slide the latch to the left to release the battery.
-
-
-
Continue holding the latch then gently pull the battery out of the device.
-
-
-
Locate the CD-ROM Drive latch.
-
-
-
Slide the latch to the right to release the CD ROM drive.
-
-
-
Continue holding the latch then gently pull the CD-ROM Drive out of the device.
-
-
-
Press firmly on each end of the speaker cover and slide it to the left.
-
-
-
Gently lift the speaker cover to remove it.
-
-
-
Lift the keyboard up from the back using a spudger(wedge side).
-
-
-
Gently lift the keyboard until only the ribbon cable remains attached.
-
-
-
Tilt the keyboard away from the screen.
-
-
-
Locate the six screws that secure the heatsink.
-
-
-
-
Remove the six screws from the heatsink using the Philips #1 screwdriver.
-
-
-
Lift the heatsink from the side closest to the laptop screen.
-
-
-
Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
-
-
-
Identify the right and left monitor end caps.
-
-
-
Pry off the end caps by putting a spudger between the monitor hinge and the end cap and prying outwards.
-
-
-
Once the end cap has been loosened by the spudger, pull outwards on the end caps.
-
-
-
Identify the 4 total screw under the end caps (2 under each end cap).
-
The two outside 16mm long screws
-
The two inside 5.4mm long screws
-
-
-
Remove the 4 screws using the Phillips #0 screwdriver.
-
-
-
Identify the center cap of the monitor.
-
-
-
Pry the center cap off by placing the spudger between the hinge and the center cap and prying upwards.
-
-
-
Identify the one 12.6mm long screw under the center cap.
-
-
-
Remove the center screw with a Phillips #0 screwdriver.
-
-
-
Lift upwards on the metal cover under the screw.
-
-
-
Identify where the left and right monitor cords are attached to the logic board
-
The base of the left monitor cord
-
The base of the right monitor cord
-
-
-
To detach the left monitor cord grab the left monitor cord at the base of the cord and pull vertically up.
-
-
-
Completely detach the left monitor cord from the logic board.
-
-
-
To detach the right monitor cord grab the right monitor cord at the base of the cord and pull vertically up.
-
-
-
Completely detach the right monitor cord from the logic board.
-
-
-
Completely remove the monitor from the computer.
-
Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.
Once the monitor has been removed, to attach the new monitor follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:05crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team 10-39, Forte Spring 2011 crwdns2935289:0Cal Poly, Team 10-39, Forte Spring 2011crwdne2935289:0
CPSU-FORTE-S11S10G39
crwdns2931471:05crwdne2931471:0
crwdns2935297:06crwdne2935297:0
