crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

Razer BlackShark V2 Ear Cushion Replacement

crwdns2915892:0crwdne2915892:0

If your Razer BlackShark V2 foam ear cushions are shedding particles or detaching from the device (Razer Blackshark V2 Troubleshooting Page, "Ear Cushions Falling Apart"), this guide will assist you in their replacement. Be sure to be mindful of which layer of the headset assembly you're taking apart and that you don't adversely damage any holds, the rubber lining under the cushions, or the headset itself when applying pressure.

crwdns2942213:0crwdne2942213:0

  1. Razer BlackShark V2 Ear Cushion Replacement, Ear Cushion: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Place the headset so that the left side is facing you.

    • The left side of the headset has the cable attachment and the volume control knob.

    crwdns2913378:0crwdne2913378:0

  2. Razer BlackShark V2 Ear Cushion Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Scoop your middle and ring finger underneath the top or bottom inner portion of the ear cushion.

    • You should feel a hard plastic ridge.

    • Pull from the hard plastic ridge, being sure not to pull from the soft cushion.

    • Slowly apply pressure to prevent damage.

    crwdns2913378:0crwdne2913378:0

  4. Razer BlackShark V2 Ear Cushion Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Pull from the hard plastic ridge, being sure not to pull from the soft cushion.

    • Slowly apply pressure to prevent damage.

    crwdns2913378:0crwdne2913378:0

  5. Razer BlackShark V2 Ear Cushion Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Razer BlackShark V2 Ear Cushion Replacement: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Once the cushion is removed, make sure the hard plastic base with the clips is attached to it.

    • If you are replacing both ear cushions, repeat Steps 1-4 for the other side. Then, insert the new ear cushions by lining up the clips in their respective holes and applying even pressure until they audibly click.

    crwdns2913378:0crwdne2913378:0
crwdns2935217:0crwdne2935217:0

crwdns2935229:02crwdne2935229:0

crwdns2862417:0crwdne2862417:0

crwdns2935291:0crwdnd2935291:01crwdnd2935291:0crwdne2935291:0

BlakeB

crwdns2935283:003/08/23crwdne2935283:0

545 crwdns2915208:0crwdne2915208:0

crwdns2935297:03crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 12

crwdns2935301:09crwdne2935301:0

crwdns2915084:0crwdne2915084:0

University of New Orleans, Team 4-3, McDonald Spring 2023 crwdns2935289:0University of New Orleans, Team 4-3, McDonald Spring 2023crwdne2935289:0

UNO-MCDONALD-S23S4G3

crwdns2931471:04crwdne2931471:0

crwdns2935297:09crwdne2935297:0

crwdns2947412:02crwdne2947412:0

Thanks - this was very helpful. It was difficult to remove the retainer clip using my fingers - I found it much easier to use the back of a spoon (with a rounded edge) and getting more leverage that way.

Peter Gu - crwdns2934203:0crwdne2934203:0

can someone pls tell me what's the size or mm of the foam?

Lorraine Corda - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 5

crwdns2936753:07crwdne2936753:0 30

crwdns2936753:030crwdne2936753:0 128

crwdns2942667:0crwdne2942667:0 3,397