crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

RIDGID Belt Sander R2740 On/Off Switch Replacement

crwdns2915892:0crwdne2915892:0

If your RIDGID R2740 Belt Sander won't turn on, the on/off switch may be defective and need to be replaced. This guide will walk you through how to replace the on/off switch on your RIDGID R2740 Belt Sander.

crwdns2942213:0crwdne2942213:0

  1. RIDGID Belt Sander R2740 On/Off Switch Replacement, Power Cord: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 RIDGID Belt Sander R2740 On/Off Switch Replacement, Power Cord: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Orient the belt sander so that the RIDGID logo is facing you.

    • Remove the six 19 mm and three 51 mm T20 screws that hold the cover into place.

    • Remove the cover from the belt sander.

    • Make sure you remember the correct placement of each screw.

    crwdns2913378:0crwdne2913378:0

  2. RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:02crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove the two 16 mm T10 screws.

    • Remove the support bracket that holds the power cord into place.

    crwdns2913378:0crwdne2913378:0

  4. RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:03crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:03crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

    • Lift the power cord from the resting grooves.

    • Rotate the switch so that the lock-on button is facing you.

    • Loosen the two 8 mm Phillips #3 screws.

    • Pull the two wires away from the switch.

    crwdns2913378:0crwdne2913378:0

  5. RIDGID Belt Sander R2740 On/Off Switch Replacement, On/Off Switch: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Undo the two screws on the backside of the switch with a Phillips #3 screw driver.

    crwdns2913378:0crwdne2913378:0

  6. RIDGID Belt Sander R2740 On/Off Switch Replacement: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Pull out the wires from the switch.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935227:0crwdne2935227:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:02crwdnd2935293:0crwdne2935293:0

Auddie Reynolds

crwdns2935283:001/10/19crwdne2935283:0

112 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 3

crwdns2915084:0crwdne2915084:0

Oregon Institute of Technology, Team S1-G1, Lancaster Winter 2019 crwdns2935289:0Oregon Institute of Technology, Team S1-G1, Lancaster Winter 2019crwdne2935289:0

OIT-LANCASTER-W19S1G1

crwdns2931471:04crwdne2931471:0

crwdns2935297:06crwdne2935297:0

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 1

crwdns2936753:030crwdne2936753:0 6

crwdns2942667:0crwdne2942667:0 797