RCA CC310 Viewfinder Replacement

crwdns2931653:01crwdne2931653:0 Viewfinder



• Slide a spudger between the plastic rail and the metal tab on the left side of the rail. Push away from the camcorder to release the flap.
• Pushing the viewfinder assembly to the right makes lifting the flap easier.
• Slide the lifted flap towards the viewfinder assembly until the viewfinder is free from the rail.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0




• Unscrew the 7mm ph#0 screw on the underside where the cable connects.
• Lift the plastic where the cable connects off of the viewfinder assembly.
• Disconnect the cable inside by pulling it apart.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0
• Unscrew two 7.0mm ph#0 screws on the underside of the viewfinder assembly.
• Lift the viewfinder plastic assembly up and remove.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Flip back the viewfinder access tab.
• Unscrew the 7.0mm ph #0 screw next to the mirror.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Lift off both sides of the plastic assembly.
• When reassembling, if the housing doesn't connect properly, try turning the focus wheel.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Lift the microphone circuit board straight up.
• Unclip the cable connected to the circuit board.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Lift plastic housing and guide the wires from underneath.
• Lift out the entire circuit board and viewfinder.
• Replace entire circuit board and viewfinder assembly.
crwdns2913378:0crwdne2913378:0
crwdns2935261:0crwdne2935261:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:07crwdnd2935293:0crwdne2935293:0

Oliver Adams

crwdns2935283:001/19/11crwdne2935283:0

629 crwdns2915208:0crwdne2915208:0

crwdns2935297:06crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 8

• 
• 
• 

crwdns2935301:05crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 5-20, Amido Winter 2011 crwdns2935289:0Cal Poly, Team 5-20, Amido Winter 2011crwdne2935289:0

CPSU-AMIDO-W11S5G20

crwdns2931471:04crwdne2931471:0

crwdns2935297:07crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0