crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Puritan Bennett 560 Internal Battery Replacement

crwdns2911024:0crwdne2911024:0
crwdns2911026:0crwdne2911026:0

crwdns2915892:0crwdne2915892:0

This guide will explain how to remove and replace the internal battery in the Puritan Bennett 560 ventilator.

Warnings:

  • Ensure the ventilator is powered off and AC power is disconnected
  • Do not try to open the battery itself under any circumstances
  • Cover the battery terminals with a non-conductive material when not in use to prevent short-circuiting.

The repair information is also available on pages 143-144 (Section 5, Pages 13-14) of the Service Manual that is linked in the documents section.

crwdns2942213:0crwdne2942213:0

  1. Puritan Bennett 560 Internal Battery Replacement, Internal Battery: crwdns2935265:01crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • REMOVAL

    • Locate the battery cover on the rear of the ventilator.

    crwdns2913378:0crwdne2913378:0

  2. Puritan Bennett 560 Internal Battery Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Using the T10 Torx screwdriver, remove the three 8mm screws on the battery cover.

    • Two screws are located on the rear of the ventilator, and one on the bottom.

    • Slide the battery cover out of the ventilator.

    • Remove the battery from the battery cover.

    crwdns2913378:0crwdne2913378:0

  3. Puritan Bennett 560 Internal Battery Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • REPLACEMENT

    • Install the battery into cover, as shown in figure.

    • Make sure the contacts on the battery line up with those in the ventilator.

    • Slide the battery and cover together into the housing.

    • While applying pressure to the cover, install the two rear screws.

    • Install the screw at the bottom of the cover.

    • Be careful not to over-tighten any screws.

    crwdns2913378:0crwdne2913378:0
crwdns2935217:0crwdne2935217:0

crwdns2935229:02crwdne2935229:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:02crwdnd2935293:0crwdne2935293:0

Theo Philliber

crwdns2935283:004/07/20crwdne2935283:0

201 crwdns2915208:0crwdne2915208:0

crwdns2935295:0crwdne2935295:0

crwdns2918514:0crwdne2918514:0: 9

crwdns2935301:06crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team S11-G20, Paton Spring 2020 crwdns2935289:0Cal Poly, Team S11-G20, Paton Spring 2020crwdne2935289:0

CPSU-PATON-S20S11G20

crwdns2931471:02crwdne2931471:0

crwdns2935297:03crwdne2935297:0

crwdns2917034:0crwdne2917034:0

I can’t seem to edit the step titles. They should show:

Step 1: Battery Removal

Step 2:

Step 3: Battery Replacement

Theo Philliber - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 1

crwdns2936753:030crwdne2936753:0 5

crwdns2942667:0crwdne2942667:0 505