crwdns2942213:0crwdne2942213:0
-
-
Disconnect all cables from the console and flip the unit over to reveal its base.
-
-
-
Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws.
-
-
-
Remove all six 4.0 mm screws from the base of the unit using a #1 Phillips screwdriver.
-
-
-
Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit.
-
-
-
Locate the fan at the front, left section of the unit.
-
-
-
Peel off the sticker holding the power cords to the unit.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Lift the connector from the motherboard with a pair of tweezers using a firm, upward force.
-
-
-
Remove all three 1.6 mm screws fastening the fan to the unit using a #1 Phillips screwdriver.
-
Gently lift and remove the fan from its compartment.
-
-
-
-
Locate the clock battery at the front, right section of the unit. The battery has a circular shape with red (+) and black (-) wires connecting to the motherboard.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Lift the connector from the motherboard with a pair of tweezers using a firm, upward force.
-
-
-
Gently lift and remove the battery from its compartment using a spudger.
-
-
-
Locate the IR sensor at the front, right corner of the unit.
-
-
-
Gently detach the ribbon cable connecting the IR sensor to the motherboard.
-
Caution: Always remove ribbon cables by the plastic handles located on either end. Gripping a ribbon cable anywhere but the provided handles can damage the cable and render the component useless.
-
-
-
Gently lift and remove the IR Sensor from its designated slot.
-
-
-
Locate the optical drive which occupies most of the space on the right side of the unit. It can be identified by the four screws with wide-diameter heads fastening the optical drive to the motherboard.
-
-
-
Remove the four 4.0 mm screws using a #1 Phillips screwdriver.
-
-
-
Locate the three ribbon cables connecting the optical drive to the motherboard.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Gently detach the ribbon cables from the motherboard using a pair of tweezers.
-
-
-
Remove any tape fastening the cables to the motherboard and gently lift and remove the optical drive.
-
-
-
Remove the 2.4 mm screw located in between the controller ports using a #1 Phillips screwdriver.
-
-
-
Gently lift and remove the motherboard and chassis from the outer shell.
-
-
-
There are a total of five 1.6 mm screws which mount the metal chassis to the motherboard.
-
Remove the screw on top and the four screws on the bottom with a #1 Phillips screwdriver.
-
-
-
Gently separate the two metal plates from the motherboard.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:035crwdne2935229:0
crwdns2947412:02crwdne2947412:0
نرجو اضافة اللغة العربية
Mi placa no tiene corriente, seguro tiene un corto quien me ayuda a solucionar, es la 77001, ya tiene botón y flex nuevo y no me da luz Led
