crwdns2894164:0crwdne2894164:0

crwdns2915892:0crwdne2915892:0

This guide will help the user replace the white plastic housing of the player, and will allow the user to replace inner parts.

crwdns2860947:0crwdne2860947:0

crwdns2890040:0crwdne2890040:0

  1. Philips PD9000 37 White Outer Housing Replacement, White Outer Housing: step 1, image 1 of 3 Philips PD9000 37 White Outer Housing Replacement, White Outer Housing: step 1, image 2 of 3 Philips PD9000 37 White Outer Housing Replacement, White Outer Housing: step 1, image 3 of 3
    • Lay the player flat so the bottom outside is showing. Using the Phillips #0 screwdriver, unscrew all the housing screws on the bottom of the player.

    • Have the player sitting upright, remove the rubber stoppers in order to get to the screw. Unscrew the inside screws by the screen using the Philips #0 screwdriver.

    • Remove the rubber stoppers for the bottom two screws as well. Unscrew the middle two screws.

  2. Philips PD9000 37 White Outer Housing Replacement: step 2, image 1 of 2 Philips PD9000 37 White Outer Housing Replacement: step 2, image 2 of 2
    • Open the disc flap and remove the screws inside with the Phillips #0 screwdriver. There will be three screws.

  3. Philips PD9000 37 White Outer Housing Replacement: step 3, image 1 of 3 Philips PD9000 37 White Outer Housing Replacement: step 3, image 2 of 3 Philips PD9000 37 White Outer Housing Replacement: step 3, image 3 of 3
    • Start removing the inside black face plate of the player by using a prying method between the white outer housing and the black face plate with a metal spudger.

    • Pull the black face plate off once you have pried it from the white housing. The bottom inside layer should pop off.

    • Using the same prying method with the metal spudger, start prying off the screens white outer housing.

  4. Philips PD9000 37 White Outer Housing Replacement: step 4, image 1 of 3 Philips PD9000 37 White Outer Housing Replacement: step 4, image 2 of 3 Philips PD9000 37 White Outer Housing Replacement: step 4, image 3 of 3
    • The light panel on the front can just pop right off.

    • To remove the metal bar against the battery, unscrew the screws with the phillips #0 screwdriver.

    • After unscrewing you can just lift the metal bar off.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

Julia Sheremet

crwdns2886885:028/09/2015crwdne2886885:0

291 crwdns2915208:0crwdne2915208:0

crwdns2886889:02crwdne2886889:0

crwdns2915084:0crwdne2915084:0

Eastern Washington University, Team 1-3, Matresse Fall 2015 crwdns2886886:0Eastern Washington University, Team 1-3, Matresse Fall 2015crwdne2886886:0

EWU-MATRESSE-F15S1G3

crwdns2858115:03crwdne2858115:0

crwdns2886889:04crwdne2886889:0

crwdns2917036:00crwdne2917036:0

crwdns2917038:0crwdne2917038:0

crwdns2894754:0crwdne2894754:0:

crwdns2894766:024crwdne2894766:0 0

crwdns2894768:07crwdne2894768:0 0

crwdns2894768:030crwdne2894768:0 0

crwdns2894770:0crwdne2894770:0 386