crwdns2915892:0crwdne2915892:0
If your camera begins malfunctioning, you may need to replace your motherboard. In this replacement guide you will first remove the battery to avoid getting shocked while working inside the camera. Then you will remove the back panel, unscrew several screws, and detach several electronic ZIF connector ribbons to replace the motherboard. See this technique on disconnecting ZIF connectors to better learn how to detach a ZIF connector ribbon.
crwdns2942213:0crwdne2942213:0
-
-
Slide the switch on the bottom of your camera from the right (LOCK) to the left (OPEN).
-
-
-
Pull down on the lever that holds the battery.
-
-
-
Push in on the SD card inside the battery housing.
-
Pull out the SD card.
-
Close the battery housing door.
Il faut modifier “Étape 4 Carte mère” par “Étape 4 Carte mémoire”, mais je n’y arrive pas.
-
-
-
-
Remove the two 5.2 mm Phillips #00 screws that are 1) below the label and 2) above the tripod mount hole on the bottom of the camera.
-
Remove the two 5.5 mm Phillips #00 screws on the side of the camera with the MIC jack.
-
Remove the two 7.0 mm Phillips #00 screws that are 1) above and 2) below the HDMI panel.
Quitar también los Phillips #?? zona de abajo del visor, desmontar ,y , quitar otros 2 phillips #?? interiores.
-
-
-
There are two screws that hold the eye piece on to the main housing, just underneath. Remove these. Once these have been removed, gently pull and remove the eye piece and remove the now accessible top two screws.
-
-
-
Gently lift up the back plate, being careful not to damage any ribbons.
-
Pull to disconnect from the motherboard the two ZIF connector ribbons attached to the back plate.
-
Set aside the back plate.
The eyepiece needs to be removed!
Remove the phillips screws from the bottom of the eyepiece, remove the eyepiece and remove the two screws at the top of the eyepiece
-
-
-
Pull to disconnect from the motherboard the seven ZIF connector ribbons.
Die Anleitung zum Öffnen von ZIF-Anschlüssen hilft leider nicht weiter. Die Plastikbügel zerbrechen beim Versuch sie nach Anleitung aufzuklappen. Diesen wesentlichen Arbeitsschritt mit Bildern zu versehen wäre vielleicht hilfreich gewesen...
-
-
-
Remove the four 5.2 mm Phillips #00 screws at the corners of the motherboard.
-
-
-
Firmly grasp the left side of the motherboard.
-
Pull out the motherboard.
FZ1000 MK2: I could not remove the motherboard by itself but it came off easily together with the metal plate.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:08crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team 70-5, Forte Winter 2016 crwdns2935289:0Cal Poly, Team 70-5, Forte Winter 2016crwdne2935289:0
CPSU-FORTE-W16S70G5
crwdns2931471:04crwdne2931471:0
crwdns2935297:015crwdne2935297:0
crwdns2947412:03crwdne2947412:0
Where do you buy a motherboard for this camera?
This article is useless, since the motherboards are not available anywhere.
Actually, Panasonic does have the part for sale. <https://panasonic.encompass.com/item/102...>
