crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2918746:0crwdne2918746:0

PSP Go Analog Joystick Replacement

crwdns2915892:0crwdne2915892:0

Use this guide to put a fresh analog joystick into the PSP Go!

crwdns2942213:0crwdne2942213:0

  1. PSP Go Analog Joystick Replacement, Back Cover: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 PSP Go Analog Joystick Replacement, Back Cover: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Unscrew the four Phillips screws on the back of the PSP Go.

    • Rotate the PSP so you can see the top of the device.

    • Unscrew the two Phillips screws next to the volume buttons.

    crwdns2913378:0crwdne2913378:0

  2. PSP Go Analog Joystick Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 PSP Go Analog Joystick Replacement: crwdns2935265:02crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Use a plastic opening tool around the perimeter of the back cover to loosen it on all sides.

    • Open the back cover by gently lifting the right side, and rotating it to the left side (as if you were opening a book).

    • Be careful not to rotate the back cover from the bottom, as you will break the plastic screw holes on top of the device.

    crwdns2913378:0crwdne2913378:0

  4. PSP Go Analog Joystick Replacement, Top Cover: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Pull the top cover upwards gently from its housing.

    crwdns2913378:0crwdne2913378:0

  5. PSP Go Analog Joystick Replacement, Bottom Plate: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 PSP Go Analog Joystick Replacement, Bottom Plate: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove the two Phillips screws holding the bottom plate.

    • Gently lift the bottom plate away from the device.

    crwdns2913378:0crwdne2913378:0

  6. PSP Go Analog Joystick Replacement, Analog Joystick: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Use a #00 Phillips screwdriver to remove both screws holding the analog joystick in place.

    crwdns2913378:0crwdne2913378:0

  7. PSP Go Analog Joystick Replacement: crwdns2935265:06crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 PSP Go Analog Joystick Replacement: crwdns2935265:06crwdnd2935265:02crwdnd2935265:02crwdne2935265:0
    crwdns2935267:0crwdne2935267:0
    Tweezers
    $4.99
    crwdns2945778:0crwdne2945778:0

    • Use a plastic opening tool to gently flip up the analog joystick's cable connector.

    • Use your fingers or tweezers to gently pull out the analog joystick cable from its connector.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935229:05crwdne2935229:0

crwdns2947410:01crwdne2947410:0

What about the plastic tab on the ribbon cable how do i attach the ribbon cable to the connector its very delicate

daniel - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 3

crwdns2936753:07crwdne2936753:0 11

crwdns2936753:030crwdne2936753:0 63

crwdns2942667:0crwdne2942667:0 22,801