crwdns2942213:0crwdne2942213:0
-
-
Using the iFixit Opening Tool, pry off the plastic part of the lens.
-
Using the T6 Torx screwdriver, unscrew the three screws.
-
-
-
Using the Phillips #00 screwdriver, unscrew the three screws.
-
Carefully swivel the metal cover out towards you.
-
Using tweezers, remove the metal washer.
-
-
-
Using the tweezers, slowly peel off the plate.
-
-
-
Using the Phillips #00 screwdriver, unscrew the two screws on the side of the camera.
-
-
-
On the opposite side, use the Phillips #00 screwdriver to unscrew both screws.
-
Take out the speaker plate.
-
Open the multi-connector cover and slide off the side panel.
-
-
-
-
Using the Phillips #00 screwdriver, unscrew the screw above the speaker.
-
On the bottom side of the camera, unscrew the two screws.
-
-
-
Open the battery compartment cover.
-
Use the Phillips #00 screwdriver to unscrew the screw in the battery compartment.
-
-
-
On the front of the camera, unscrew the two screws shown.
-
Gently pull on the side until the camera is separated from the back panel.
-
Remove the shutter and power button.
-
-
-
Use the Phillips #00 screwdriver to unscrew the four screws on the front of the camera.
-
Unscrew the shutter using the Phillips #00 screwdriver.
-
-
-
Release the top holding using a spudger.
-
Slowly and carefully separate the front and back of the camera, exposing the electrical ribbons.
-
-
-
Using the spudger and tweezers if needed, remove the ribbons from the computer chips.
-
-
-
Remove the 1.0 cm and the 0.8 mm screws.
-
Peel off tape and remove ribbons.
-
Remove black plastic cover and unscrew the 1.1 cm screw.
-
-
-
Release ribbons carefully using either tweezers or a spudger.
-
Remove the 1.1 cm screw.
-
-
-
Push A/V port away from you carefully using a spudger.
-
Slowly take out the motherboard and the speaker microphone.
-
Collect the metal washer plate from the top right corner of the motherboard (now loose).
-
-
-
With a spudger or finger, slowly take out the battery hinged to the motherboard.
-
Take out motherboard.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014 crwdns2935289:0University of Illinois Urbana-Champaign, Team 1-2, Scrogum Spring 2014crwdne2935289:0
UICU-SCROGUM-S14S1G2
crwdns2931471:05crwdne2931471:0
crwdns2935297:010crwdne2935297:0
crwdns2944067:03crwdne2944067:0
what is the voltage, and capacitance of the main flash capacitor? diameter and length? I want to replace mine as my 'flash charging' symbol constantly flashes and flash does not fire.
thanks for the writeup! I have more confidence in repairing my 10+ year old camera
the cap is 330uF and 90V
dimensions:
11.94mm diameter
25.65mm length
How would I go about extracting the camera module and hooking it up to an arduino?
My cam got saltwater damage however it still turns on for a few seconds before turning off again
