crwdns2915892:0crwdne2915892:0
Follow this guide to replace your Nokia 6 loudspeaker.
In this guide, you do not have to take apart the front and rear facing cameras from the motherboard. Simply removing the motherboard will expose the parts needed for the next steps.
crwdns2942213:0crwdne2942213:0
-
-
Insert the SIM card ejection tool into the hole on the left side of the phone.
-
Remove the SIM card and microSD card.
-
-
-
Lay overlapping strips of clear packing tape over the Nokia 6's display until the whole screen is covered.
-
-
-
To soften the adhesive, use a heat gun and heat one edge of the phone for five minutes.
-
To use the heat gun, plug it into an outlet.
-
-
-
Take a Jimmy and slide it under the glass after the adhesive has been softened.
-
Place a pick under the glass after lifting with the pry tool so that the screen won't re-adhere to the frame again.
-
-
-
Use a Phillips #000 screwdriver to remove the 1 mm x 1.4 mm screw holding down the metal bracket over the screen ribbon connector.
-
-
-
Remove the metal bracket with a tweezer.
-
-
-
-
Use a spudger to disconnect the screen ribbon connector and free the display assembly.
-
Carefully remove the screen from the device.
-
-
-
Disconnect the battery connector with a spudger.
-
-
-
Use a Phillips #00 screwdriver to remove the 1.2 mm x 2.2 mm screw in the upper hand corner of the phone.
-
Use tweezers to remove the bracket.
-
-
-
Detach the cable with the black nylon spudger.
-
Detach the home button and remove it from the device.
-
-
-
Remove 18 screws.
-
There is one 1 mm x 1.4 mm screw that needs to be removed by a Phillips #000 screwdriver.
-
One of the screws is 1.2 mm x 4.2 mm and will be removed by a Phillips #00.
-
The remaining 16 screws can be removed by the Phillips #00 screwdriver and are 1.2 mm x 2.2 mm.
-
-
-
Decouple the midframe with the spudger and remove the midframe from the device.
-
-
-
Remove the bracket with tweezers.
-
-
-
Detach the two cables with the spudger.
-
Detach the cable with a pair of tweezers.
-
-
-
Remove six screws.
-
Two of these screws are 1.0 mm x 1.4 mm and need to be removed by a Phillips #000 screwdriver.
-
The remaining four screws are 1.2 mm x 2.2 mm and are removed by a Phillips #00 screwdriver.
-
-
-
Remove the motherboard from the Nokia 6 with the spudger.
-
-
-
With tweezers, lift the wire by the microUSB port and the microphone unit.
-
-
-
Remove three screws.
-
Two of these are 1 mm x 1.4 mm and can be removed by a Phillips #000.
-
One of the screws is 1.2 mm x 2.2 mm and can be removed by a Phillips #00.
-
-
-
Remove the microUSB port and the microphone by lifting the unit with a spudger.
-
-
-
Use a spudger to remove the loudspeaker from the phone.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935227:0crwdne2935227:0
crwdns2915084:0crwdne2915084:0
Cal Poly, Team S9-G15, Maness Spring 2019 crwdns2935289:0Cal Poly, Team S9-G15, Maness Spring 2019crwdne2935289:0
CPSU-MANESS-S19S9G15
crwdns2931471:04crwdne2931471:0
crwdns2935297:014crwdne2935297:0
crwdns2917034:0crwdne2917034:0
Great article and just one question. “To reassemble your device, follow these instructions in reverse order.” That’s ok until the screen needs to be glued back so advice on doing that would be appreciated.
