crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Milwaukee Hex Impact Driver 2753-20 Trigger Replacement

crwdns2915892:0crwdne2915892:0

The removal of the trigger is relatively challenging. It is the central part of the tool and has some wiring attached. Practice extreme caution and make sure the battery is removed.

crwdns2942213:0crwdne2942213:0

  1. Milwaukee Hex Impact Driver 2753-20 Trigger Replacement, Battery: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Milwaukee Hex Impact Driver 2753-20 Trigger Replacement, Battery: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • While pinching the red locking buttons, pull the battery away from the front of the drill until the battery is fully removed.

    • The battery is missing from this device so its removal is being mimed.

    crwdns2913378:0crwdne2913378:0

  2. Milwaukee Hex Impact Driver 2753-20 Trigger Replacement, Milwaukee Hex Impact Driver 2753-20 Cover Removal: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Using the Torx T10 screwdriver, remove the six 17 mm screws on the outside of the handle.

    • Remove the two 40 mm Torx T10 screws near the bottom of the cover.

    crwdns2913378:0crwdne2913378:0

  4. Milwaukee Hex Impact Driver 2753-20 Trigger Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Milwaukee Hex Impact Driver 2753-20 Trigger Replacement: crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Carefully remove the cover.

    • If there is buildup from sawdust or sediment it might be a little difficult to take apart.

    crwdns2913378:0crwdne2913378:0

  5. Milwaukee Hex Impact Driver 2753-20 Trigger Replacement, Trigger: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Milwaukee Hex Impact Driver 2753-20 Trigger Replacement, Trigger: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Lift the trigger assembly from the device. It is connected to the circuit board by wires.

    • Carefully desolder the wires off of the trigger assembly using a soldering iron on medium heat.

    • Refer to this guide for proper desoldering technique.

    crwdns2913378:0crwdne2913378:0

  6. Milwaukee Hex Impact Driver 2753-20 Trigger Replacement: crwdns2935265:05crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove the trigger assembly from the device.

    • Replace old trigger assembly with replacement part no. 14-20-0013.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935227:0crwdne2935227:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:02crwdnd2935293:0crwdne2935293:0

Alex Larson

crwdns2935283:001/16/19crwdne2935283:0

243 crwdns2915208:0crwdne2915208:0

crwdns2935297:02crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 7

crwdns2935301:04crwdne2935301:0

crwdns2915084:0crwdne2915084:0

University of Alabama, Team S2-G3, Bedsole Spring 2019 crwdns2935289:0University of Alabama, Team S2-G3, Bedsole Spring 2019crwdne2935289:0

UA-BEDSOLE-S19S2G3

crwdns2931471:03crwdne2931471:0

crwdns2935297:07crwdne2935297:0

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 5

crwdns2936753:030crwdne2936753:0 37

crwdns2942667:0crwdne2942667:0 4,494