crwdns2915892:0crwdne2915892:0
Keyboards can be damaged when liquids are spilled on them. Without a functioning keyboard, it can be very difficult to use the Maylong MN-1000P. Replacing a keyboard is not difficult and requires only a few simple tools.
crwdns2942213:0crwdne2942213:0
-
-
Place the netbook top down, with the opening of the netbook facing you.
-
-
-
Remove the six 6mm Phillips #00 screws from the netbook.
-
-
-
Remove the sticker in the middle of the netbook.
-
Remove the middle 6mm Phillips #00 screw.
-
-
-
Using two plastic opening tools, pry off the bottom of the netbook by going around the edges.
-
-
-
Remove the bottom of the netbook by lifting the corners.
-
-
-
Pinch the red and black wires connected to the section closest to the small white connector, and pull to remove them from the motherboard.
-
-
-
Remove the six 6mm Phillips #00 screws from both sides of the netbook.
-
-
-
Pull the top of the computer and the back side of the computer away from each other until they are detached.
-
Flip the entire computer over so you can see both the screen and keyboard.
-
-
-
-
Remove all the black circular pads from around the screen.
-
Remove all 6mm Phillips #00 screws from around the screen bezel.
-
-
-
Using a plastic opening tool, pry off the screen bezel.
-
After detaching the screen bezel, pull up on the bezel near the hinge area.
-
-
-
Use tweezers to gently pull on the black and white wires at the top of the netbook until the white connector detaches.
-
-
-
Use your fingers to pull on the green, red, black, and white intertwined wires at the bottom of the netbook until the white connector detaches.
-
-
-
Detach the wide yellow ribbon cable connected to the screen from the computer.
-
-
-
Flip the computer over.
-
Disconnect the red, green, black, and white intertwined wires from the connector to the motherboard.
-
-
-
Remove the black tape holding down the red, green, black, and white intertwined wires.
-
Remove the screen.
-
-
-
Remove the six 6mm Phillips #00 screws from the motherboard.
-
-
-
Remove the two 6mm silver screws from the small circuit board connected to the motherboard by the red and black wires.
-
-
-
Remove the two small black speakers on the corners connected to the motherboard by the black and red wires.
-
-
-
Disconnect the black connectors from the motherboard by pulling on the white ribbon cable.
-
-
-
Remove the black covered wire connected to the motherboard by pulling the white ribbon cable away from the motherboard.
-
-
-
Using a spudger, remove the gold cylinder out of the indent at the bottom of the computer.
-
-
-
Lift the motherboard up.
-
Remove the motherboard by detaching the clear tape from underneath the motherboard.
-
-
-
Hold the keyboard panel with the back facing you.
-
Using your thumbs, push on the silver squares.
-
-
-
Flip the netbook over so the keyboard is facing upwards.
-
Insert a spudger between the keyboard and the top of the plate.
-
Lift the keyboard up and away from the mouse pad to remove.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2915084:0crwdne2915084:0
Eastern Washington University, Team S1-G3, Carnegie Winter 2020 crwdns2935289:0Eastern Washington University, Team S1-G3, Carnegie Winter 2020crwdne2935289:0
EWU-CARNEGIE-W20S1G3
crwdns2931471:03crwdne2931471:0
crwdns2935297:05crwdne2935297:0
