crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

crwdns2931315:0crwdnd2931315:0crwdne2931315:0

crwdns2942213:0crwdne2942213:0

  1. crwdns2935201:0crwdne2935201:0 crwdns2935203:0crwdne2935203:0

    : crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 : crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove the four rubber caps from the back by using the Phillips #00 screwdriver.

    crwdns2913378:0crwdne2913378:0

  2. crwdns2935201:0crwdne2935201:0 crwdns2935203:0crwdne2935203:0

    : crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Remove the four screws holding the cover in place by using the Phillips #00 screwdriver.

    crwdns2913378:0crwdne2913378:0

  4. crwdns2935201:0crwdne2935201:0 crwdns2935203:0crwdne2935203:0

    : crwdns2935265:03crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 : crwdns2935265:03crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Remove the back cover from the device by separating the back cover along its seam.

    • Slowly lift the cover—the speaker is screwed onto the back cover and is connected to the circuit board.

    crwdns2913378:0crwdne2913378:0

  5. crwdns2935201:0crwdne2935201:0 crwdns2935203:0crwdne2935203:0

    : crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 : crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Pull the speaker cord, horizontally, by its base, away from the motherboard.

    • When reassembling, make sure that you plug the terminal in the same way. The black wire should be on the side farthest from the battery.

    crwdns2913378:0crwdne2913378:0

  6. crwdns2935201:0crwdne2935201:0 crwdns2935203:0crwdne2935203:0

    : crwdns2935265:05crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 : crwdns2935265:05crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 : crwdns2935265:05crwdnd2935265:03crwdnd2935265:03crwdne2935265:0

    • Disconnect the battery connector from the circuit board.

    • Pry the battery off the circuit board. The adhesive attaching it shouldn't require any other tools.

    crwdns2913378:0crwdne2913378:0
crwdns2935217:0crwdne2935217:0

crwdns2935229:04crwdne2935229:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:03crwdnd2935293:0crwdne2935293:0

Ross Light

crwdns2935283:004/12/10crwdne2935283:0

217 crwdns2915208:0crwdne2915208:0

crwdns2935297:06crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 12

crwdns2935301:09crwdne2935301:0

crwdns2944067:00crwdne2944067:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 0

crwdns2936753:07crwdne2936753:0 15

crwdns2936753:030crwdne2936753:0 19

crwdns2942667:0crwdne2942667:0 10,523