crwdns2915892:0crwdne2915892:0
If you have cracked your screen or if you no longer see an image on your screen, its time to replace your screen. Learn how to do that in this guide.
crwdns2942213:0crwdne2942213:0
-
-
Remove the 4.9 mm torx head screws located on the camera plate on the back of the phone
-
-
-
Remove the 3.65 mm Torx head screws at the bottom of the phone.
-
-
-
Remove the SIM card tray by pushing a pin into the hole on the side of the phone.
-
-
-
Push the Spudger along the gap between the phone and the backplate to separate them.
-
-
-
Carefully pull the backplate away from the phone.
-
-
-
Peel away protective the film using your hands.
-
-
-
Remove any adhesive strips holding the battery in place gently using a fingernail or spudger.
-
-
-
-
Disconnect the orange battery ribbon cable by gently lifting with a spudger.
-
-
-
Insert a fingernail or spudger into either side of the battery and lift upward.
-
Remove the battery from phone.
-
-
-
Remove the 3.15mm Phillips Head #000 screws from motherboard.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Disconnect the two ribbon cables by gently lifting on the black hinges and pulling away with tweezers
-
-
-
Gently disconnect the rear-camera connector
-
-
-
Gently remove the front-facing camera by gently lifting on the connector tab.
-
Remove the other connector by gently lifting with a spudger.
-
-
-
Pry off the plastic brace along the top edge of the phone
-
-
-
Remove the antenna connected to the bottom piece of the screen plate
-
-
-
Gently lift the motherboard off the frame
-
Pull the camera out from behind the motherboard
-
-
-
Using a spudger, disconnect the charging port assembly cable and the screen connection cable.
-
Remove the motherboard completely.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Gently lift the speaker out of its housing by inserting the tweezers under the speaker.
-
-
-
Remove the 3.6 mm Phillips head screws from the charging assembly
-
-
-
Gently peel the flat cable away from the screen
-
Gently lift the charging assembly using a spudger
-
-
-
Your device is now ready for reassembly with the replacement screen.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:02crwdne2935229:0
crwdns2915084:0crwdne2915084:0
USF Tampa, Team 18-3, Blackwell Fall 2016 crwdns2935289:0USF Tampa, Team 18-3, Blackwell Fall 2016crwdne2935289:0
USFT-BLACKWELL-F16S18G3
crwdns2931471:04crwdne2931471:0
crwdns2935297:012crwdne2935297:0
crwdns2947412:03crwdne2947412:0
can the glass and LCD be separated after step 21?
No, it can’t. It strips te polarizing layer off the LCD and ruins it, so dont buy just the digitizer to repair. Having said that, also dont buy the LCD either as its not worth the cost as a new phone will be cheaper or similar price.
I broke my vibe z2pro screen, can anyone recommend a cheap but good display available for replacement?
Thank you!
