crwdns2942213:0crwdne2942213:0
-
-
Use a Phillips #0 screwdriver to unscrew the five screws that secure the back cover to the laptop.
-
-
-
Use a Jimmy to lift the cover directly up off of the locating pins.
-
Remove the back cover.
-
-
-
Use the Phillips #0 screwdriver to remove the four 5 mm screws that secure the battery to the laptop frame.
-
-
-
Take out the battery by lifting it from the top edge of the laptop, and then pulling away from the motherboard.
-
-
-
Use a Phillips #0 screwdriver to remove the single screw that secures the SSD to the motherboard.
-
-
-
Carefully remove the SSD by lifting it and pulling it out of the pins towards the battery of the laptop.
-
-
-
Carefully peel the thermal pad off of the back of the SSD.
-
-
-
Use a Phillips #0 screwdriver to loosen the four screws that secure the fan to the motherboard.
-
-
crwdns2935267:0crwdne2935267:0Nylon Tipped Tweezers$4.99
-
Use nylon tipped tweezers, or your fingers, to gently pull the fan's power cable towards the SSD, disconnecting it from the pins.
-
-
-
-
Use a plastic opening pick to lift the fan mount.
-
Use your fingers to gently pull the fan diagonally away from where it is connected.
-
-
-
Turn the fan over to expose the interior.
-
If necessary, clean out the fan or wipe away and replace the thermal paste.
-
-
-
Remove each of the 7 main ribbon cables that connect the motherboard to the rest of the laptop.
-
Detach the last ribbon cable in the same way as before.
-
For the red and orange cables, use a spudger to lift the black plastic bar.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Place a spudger under the cables to disconnect them from the WLAN card.
-
-
-
Use a Phillips #00 screwdriver to remove the two 3mm screws that secure the IO bracket.
-
-
-
Remove the two 3mm antenna bracket screws using a Phillips #00 screwdriver.
-
-
-
Lift from the location of the screw towards you. Then pull towards the screw side to remove the bracket.
-
-
-
Lift the white and black wires from their press on connections. Make sure to grab the connector head, not the wire itself
-
-
-
Remove and unscrew the two 5mm screws with a Phillips #0 screwdriver.
-
-
-
Using an iFixit SIM card screw head tip, apply pressure to the hole to disconnect the SD card slot from the device.
-
-
-
Use a Phillips #00 screwdriver to remove each of the four remaining 3mm screws securing the motherboard to the device.
-
-
-
Lift from the top of the motherboard towards you.
-
Pull away from the IO port side to remove the motherboard.
-
-
-
Carefully remove cord from daughterboard.
-
-
-
Use a PH0 screwdriver to remove the three 2mm screws holding the daughterboard in place.
-
-
-
Use a PH0 screwdriver to remove the two 2mm screws holding the USB port in place.
-
-
-
Remove the tape covering screws holding the keyboard in place.
-
-
-
Remove the seventy-two 0.5mm screws holding keyboard in place.
-
-
-
Carefully push the keyboard from the front, starting at the edge (Left edge is depicted).
-
![Lenovo ThinkPad X1 Carbon 6th Gen Keyboard Replacement, Daughterboard [AUX]: crwdns2935265:022crwdnd2935265:01crwdnd2935265:01crwdne2935265:0](https://guide-images.cdn.ifixit.com/igi/mx5Oo4ArkK5GZZhS.medium)
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:07crwdne2935229:0
crwdns2915084:0crwdne2915084:0
The Citadel Military College of South Carolina, Team 1-8, Eggleston Fall 2022 crwdns2935289:0The Citadel Military College of South Carolina, Team 1-8, Eggleston Fall 2022crwdne2935289:0
CMCSC-EGGLESTON-F22S1G8
crwdns2931471:03crwdne2931471:0
crwdns2935297:04crwdne2935297:0
crwdns2947412:02crwdne2947412:0
Thanks for posting that. What a project!
Excelente Pagina muy buen aporte
