Kindle 1st Generation SD Card Reader Replacement

crwdns2931653:01crwdne2931653:0 Battery

• Slide the grey plastic cover laterally off the back of the device.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:02crwdne2931653:0



• Use a plastic opening tool to lift the battery on the side closest to the edge of the device.
• Unplug the battery from the device by pinching the white connector and pulling.
• Do not yank the battery or try to disconnect the battery by pulling the wires.
crwdns2913378:0crwdne2913378:0
crwdns2935261:0crwdne2935261:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:03crwdne2931653:0 SD Card Reader
• Unscrew eight (8) Phillips #00 screws (3 mm).
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:04crwdne2931653:0
• Start at one side of the device. Use a plastic opening tool to separate the casing of the device. Slowly work your way around the entire device.
• Avoid prying between the buttons and the device. This could cause damage to the buttons.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:05crwdne2931653:0
• Unscrew the two (2) Phillips #00 screws (3 mm) which fasten the metal casing shield.
• Slowly remove the metal casing shield by lifting it and carefully peeling up the tape.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:06crwdne2931653:0
• Remove the four (4) Phillips #00 screws (3 mm) which fasten the SD Card Reader.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0
crwdns2931653:07crwdne2931653:0
• Lift the flap attaching the blue and white ribbon cable to the motherboard by lifting it vertically with a spudger.
• The flap is connected via a hinge. Once you lift the flap, it will stay up and the cable will be lose. Remember to snap it back down during reassembly.
• Carefully lift the SD Card Reader vertically from the motherboard.
crwdns2913378:0crwdne2913378:0
crwdns2934285:0crwdne2934285:0
crwdns2934285:0crwdne2934285:0
crwdns2917038:0crwdne2917038:0
1024
crwdns2891542:0crwdne2891542:0 crwdns2934287:0crwdne2934287:0

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:04crwdnd2935293:0crwdne2935293:0

Samantha Manning

crwdns2935283:006/04/13crwdne2935283:0

766 crwdns2915208:0crwdne2915208:0

crwdns2935297:06crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 11

• 
• 
• 

crwdns2935301:08crwdne2935301:0

crwdns2915084:0crwdne2915084:0

University of Kentucky Louisville, Team 1-1, Chamberlain Spring 2013 crwdns2935289:0University of Kentucky Louisville, Team 1-1, Chamberlain Spring 2013crwdne2935289:0

LOUISVILLE-CHAMBERLAIN-S13S1G1

crwdns2931471:02crwdne2931471:0

crwdns2935297:07crwdne2935297:0

crwdns2942557:0crwdne2942557:0

crwdns2942955:0crwdne2942955:0

crwdns2852917:0crwdne2852917:0