crwdns2915892:0crwdne2915892:0
There are four speakers located on the base of the JBL Pulse 3 under the speaker grill.
crwdns2942213:0crwdne2942213:0
-
-
Lay the JBL Pulse 3 on its side as shown in the picture.
-
Use a plastic opening tool to lift the top right corner of the speaker grill. A small amount of force is necessary to remove the grill.
-
-
-
Repeat step 1 for bottom right corner of speaker grill.
-
-
-
After pulling the right side of the grill off, place thumb underneath grill as shown in the picture.
-
Lift and pull straight out to pull grill off the posts.
-
-
-
Repeat steps 1-3 for the left side of the speaker grill on the JBL Pulse 3. The speaker grill should now be completely removed from the JBL Pulse 3.
-
-
-
Use a Phillips #00 screwdriver to remove the six black 6mm screws on the inside of the top of the bottom section.
-
-
-
Turn the JBL Pulse 3 right-side up and unscrew the top ring of the device. A small amount of force and/or a cotton cloth may be necessary to remove this piece.
-
-
-
-
Remove the six 5mm screws on top of the JBL Pulse 3 with a Phillips #0 screwdriver.
-
-
-
Pull off the top disc of the JBL Pulse 3.
-
-
-
Remove the five 7mm screws on the inside of the JBL Pulse 3 with a Phillips #1 screwdriver.
-
-
-
Peel off black, taped-on electrical lead from the inside side of the JBL Pulse 3.
-
-
-
Pull the top section of the JBL Pulse 3 up. The outside casing to the JBL Pulse 3 should now be removed.
-
-
-
Use a Phillips #2 screwdriver to remove the six 11 mm screws that circle the bottom of the LED light display.
-
Pull the LED light display off of the JBL Pulse 3 base.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Use tweezers to pull the five connections off of the LED light display.
-
-
-
Using a Phillips #0 screwdriver, remove the two black 8mm screws on the bottom of the LED light display.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Pull out the motherboard slightly from the LED light display as shown. Using tweezers, unplug the three connections attached to the motherboard.
-
-
-
Pull the rest of the motherboard out from the LED light display.
-
Using wire cutters, snip the black wire connecting to the base of the JBL Pulse 3 at the base of the motherboard. The motherboard should now be removed from the JBL Pulse 3.
-
-
-
Using a Phillips #2 screwdriver, remove the four 10mm screws on the corner of the speaker on the side of the base of the JBL Pulse 3.
-
-
-
Pull out the speaker and cut the black and red wire with wire cutters. The speaker should now be removed from the JBL Pulse 3.
-
To reassemble your device, follow these instructions in reverse order.
Note: To finish replacing the speaker, you must solder both wires back on to the new speaker.
To reassemble your device, follow these instructions in reverse order.
Note: To finish replacing the speaker, you must solder both wires back on to the new speaker.
crwdns2915084:0crwdne2915084:0
Central Washington University, Team S1-G2, Pengilly Fall 2018 crwdns2935289:0Central Washington University, Team S1-G2, Pengilly Fall 2018crwdne2935289:0
CWU-PENGILLY-F18S1G2
crwdns2931471:03crwdne2931471:0
crwdns2935297:012crwdne2935297:0
crwdns2947412:02crwdne2947412:0
My speaker is making weird noises. It sounds like being crack. Do I need to replace the speaker or try to teardown to clean up the dust?
Hey Mates. Tell me please, somebody knows , the size of the replacement speaker and it fit from jbl charge 3 or some models? Thanks
