crwdns2915892:0crwdne2915892:0
If the buttons are not working, and you have tried other troubleshooting technique, you can use this guide to remove and replace just the buttons, rather than having to buy a whole new speaker.
crwdns2942213:0crwdne2942213:0
-
-
Insert the flat edge of the metal spudger underneath the corner of the outer case.
-
Use the spudger to pry open the plastic clips that secure the outer case.
-
-
-
Once all the clips are released, you will be able to pull up that edge of the case.
-
-
-
Once one side is released, complete the previous two steps with the other side.
-
-
-
Once all the clips are removed, you can gently remove the outer case.
-
The case is now fully removed. Now a new case will be attached by putting the case into position and pushing on the clips to reattach them.
-
-
-
Begin by unscrewing the four 9.6 mm-long screws with the Philips #00 screwdriver.
-
-
-
-
Once screws are fully out make sure to carefully pull out so the wires connected don't get damaged.
-
-
-
Once you carefully lift up the speaker, gently disconnect the wire that connects the speaker to the motherboard.
-
-
-
Once connection has been disconnected you can lift the speaker completely out.
-
-
-
The next part needed to remove covers each side and the power and bluetooth buttons in a middle strip along the speaker.
-
Begin (as shown in the second picture) by unscrewing the two screws (17mm each) with the Philips #00 screwdriver.
-
Then flip the device around and unscrew the other two screws (17 mm each) on the other side just the same.
-
-
-
Once all the screws are removed, pull the passive radiator bracket on either end off.
-
Set the passive radiator bracket to the side. It is not needed for the buttons replacement.
-
-
-
Next you must remove the passive radiator.
-
To do so use the metal spudger to undo the clips holding it down.
-
Once the clips on both sides are removed, you can pull the left and right passive radiators off the device.
-
-
-
Once the speaker is removed, you must go in through the hole where the speaker was for this step.
-
There you can use tweezers or your fingers to unhook the connection of the buttons board to the rest of the device.
-
-
-
Peel the rubber cover off using a metal spudger. It may be very sticky, so you may need to pull hard.
-
Then peel the cover off using your fingers.
-
-
-
Again use the spudger to pull the buttons board off.
-
-
-
Use the metal spudger to again pull the board containing the power and bluetooth buttons off from the device. It is located next to the strap.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2915084:0crwdne2915084:0
UMass Dartmouth, Team 3-5, Konn Fall 2023 crwdns2935289:0UMass Dartmouth, Team 3-5, Konn Fall 2023crwdne2935289:0
UMASSD-KONN-F23S3G5
crwdns2931471:04crwdne2931471:0
crwdns2935297:05crwdne2935297:0
crwdns2917034:0crwdne2917034:0
I think the newer JBL Flip 5 speakers have updated internals. I received a Flip 5 as a gift years ago and recently had to replace the battery using the tutorials on this website, and it went off without a hitch. I decided to buy another Flip 5 to use the party feature; I accidentally dropped it, and the buttons on the side stopped working. This is when I found out that the internals of my two JBL Flip 5 speakers looked different. This is only my second time trying to repair something on my own, any suggestions would be greatly appreciated.
