crwdns2915892:0crwdne2915892:0
Within this guide, the user will learn how to remove the speakers and check if speakers are functioning properly as well as how to replace them.
crwdns2942213:0crwdne2942213:0
-
-
Begin by removing the rubber caps on both sides of the JBL Flip 2 by using the black spudger to get in between the creases.
-
-
-
Remove the eight 7.0 mm Phillips #1 screws on both sides of the JBL Flip 2.
-
-
-
The NFC chip is glued onto the side of the device. Use the black spudger to separate the mic from the surface.
-
Gently slide the NFC chip into the device through the slot that the wire comes from.
-
-
-
Peel the black rubber piece from one end to the other.
-
-
-
Remove the two 7.0 mm Phillips #1 screws.
-
Carefully detach the silver plastic cover by pulling both ends off.
-
Separate the silver plastic piece by pulling it off from the middle.
-
-
-
Using a flat-head screwdriver or spudger, pry out the 8 metal nibs on the back side of the speaker.
-
Repeat the same process for the 4 remaining metal nibs (two on each end).
-
-
-
Expand the metal casing and carefully slide it off the speaker.
-
-
-
-
Using the driver adapter, first insert the #4 socket into the driver; followed by the #1 Philip's head bit in order to reach the three 13.0 mm screws.
-
-
-
Using the classic spudger, get underneath the black tape strips found on both side of the device.
-
After lifting a portion of the tape off of the device, gently peel the tape off of the device, making sure to keep it intact.
-
There is another piece of tape on the side of the device with the control buttons. Lift the tape with the classic spudger and then peel the rest of the tape off.
-
-
-
Wedge a spudger between the two halves where the tape was to pry the device open.
-
-
-
Use the black spudger to disconnect the speaker cord from it's socket.
-
-
-
Use the black spudger to disconnect the auxiliary wire from its socket.
-
-
-
Carefully remove the cable connecting the control chip to the motherboard.
-
-
-
Using the black spudger, carefully remove the cord connecting the battery to the motherboard.
-
-
-
Carefully remove the cable connecting the nfc chip to the motherboard.
-
-
-
Remove the two 7.0 mm Phillips #1 screws.
-
-
-
Remove the metal bar that was held in place by the screws.
-
-
-
Unscrew the the other four 7.0 mm Phillips #1 screws around the speakers.
-
-
-
Gently remove the speakers from the slots.
-
-
-
Check the speaker connections to see they are loose.
-
If the connections are loose, they will need to be re-soldered. For information on how to do so, click here.
-
-
-
Remove the connections from the speakers.
-
Replace the old speakers by soldering the four wires onto each connector of the new speakers.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:028crwdne2935229:0
crwdns2915084:0crwdne2915084:0
USF Tampa, Team 11-2, Cheng Spring 2016 crwdns2935289:0USF Tampa, Team 11-2, Cheng Spring 2016crwdne2935289:0
USFT-CHENG-S16S11G2
crwdns2931471:04crwdne2931471:0
crwdns2935297:08crwdne2935297:0
crwdns2944067:018crwdne2944067:0
Where to buy the speakers for JBL flip 2! Pls post it's urgent!
Since I wasn’t in the US and shipping cost from the Dayton speakers were prohibitvely, I ended up finding the speakers form China. The upside is that they are easier to install, since you dont have to cut down the lateral support, the downside is that they are 6 Ohms and have a lower quality. Though I worked for me.
Can somebody send a link for the replacement speakers pls.
Hey, maybe you have the link? :)
What is the size and ohmz and watts of the speaker?
