crwdns2936637:0crwdne2936637:0 crwdns2853008:0crwdne2853008:0 crwdns2861143:0crwdne2861143:0

Iomega Z100S2 Motherboard Replacement

crwdns2942213:0crwdne2942213:0

  1. Iomega Z100S2 Motherboard Replacement, Case: crwdns2935265:01crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement, Case: crwdns2935265:01crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Push in the plastic tab that can be seen through cracks in the front left corner using a spudger.

    crwdns2913378:0crwdne2913378:0

  2. Iomega Z100S2 Motherboard Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Move down the same side and push in the plastic tab.

    crwdns2913378:0crwdne2913378:0

  3. Iomega Z100S2 Motherboard Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Move to the front right side and once again push in the plastic tab.

    • There is not a fourth tab to push in after this one.

    crwdns2913378:0crwdne2913378:0

  4. Iomega Z100S2 Motherboard Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement: crwdns2935265:04crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Grab the cover by the front side and pull upwards.

    • You might encounter some resistance. Pull firmly, but don't yank it.

    crwdns2913378:0crwdne2913378:0

  5. Iomega Z100S2 Motherboard Replacement: crwdns2935265:05crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement: crwdns2935265:05crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Tilt the front case down until the pegs detach from the bottom of the case.

    • Lift up and outward.

    • The motherboard will be loose at this point.

    crwdns2913378:0crwdne2913378:0

  7. Iomega Z100S2 Motherboard Replacement, Disk Reader: crwdns2935265:06crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement, Disk Reader: crwdns2935265:06crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Unhook the two springs from the front plastic hooks.

    • The black side rails of the reader should easily slide forward and off.

    crwdns2913378:0crwdne2913378:0

  8. Iomega Z100S2 Motherboard Replacement: crwdns2935265:07crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • There is a white tab connected to the motherboard. Pull it upward by gently rocking it back and forth.

    • The tab does not come completely out, it only slides up slightly, so don't rip it out!

    crwdns2913378:0crwdne2913378:0

  9. Iomega Z100S2 Motherboard Replacement: crwdns2935265:08crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement: crwdns2935265:08crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Grab the reader by its sides and gently pull it upward.

    • There are two wires still connected to the bottom of the reader that haven't been detached.

    crwdns2913378:0crwdne2913378:0

  10. Iomega Z100S2 Motherboard Replacement: crwdns2935265:09crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    crwdns2935267:0crwdne2935267:0
    Tweezers
    $4.99
    crwdns2942207:0crwdne2942207:0

    • Disconnect the white wires by using tweezers to gently pull the bottom connector toward you.

    crwdns2913378:0crwdne2913378:0

  11. Iomega Z100S2 Motherboard Replacement: crwdns2935265:010crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement: crwdns2935265:010crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Disconnect the thin ribbon wire by using tweezers to gently pull the connector at the bottom toward you.

    crwdns2913378:0crwdne2913378:0

  12. Iomega Z100S2 Motherboard Replacement: crwdns2935265:011crwdnd2935265:01crwdnd2935265:01crwdne2935265:0

    • Lift the reader up and out from the device.

    crwdns2913378:0crwdne2913378:0

  13. Iomega Z100S2 Motherboard Replacement, Motherboard: crwdns2935265:012crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement, Motherboard: crwdns2935265:012crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Use a T6 Torx Screwdriver to remove the 1.3 mm screw at the back of the motherboard.

    crwdns2913378:0crwdne2913378:0

  14. Iomega Z100S2 Motherboard Replacement: crwdns2935265:013crwdnd2935265:01crwdnd2935265:02crwdne2935265:0 Iomega Z100S2 Motherboard Replacement: crwdns2935265:013crwdnd2935265:02crwdnd2935265:02crwdne2935265:0

    • Gently lift the motherboard and back case out from the bottom case.

    crwdns2913378:0crwdne2913378:0
crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2862417:0crwdne2862417:0

crwdns2935293:0crwdnd2935293:03crwdnd2935293:0crwdne2935293:0

Ezery Kennedy

crwdns2935283:010/05/10crwdne2935283:0

288 crwdns2915208:0crwdne2915208:0

crwdns2935297:02crwdne2935297:0

crwdns2918514:0crwdne2918514:0: 11

crwdns2935301:08crwdne2935301:0

crwdns2915084:0crwdne2915084:0

Cal Poly, Team 7-53, Amido Fall 2010 crwdns2935289:0Cal Poly, Team 7-53, Amido Fall 2010crwdne2935289:0

CPSU-AMIDO-F10S7G53

crwdns2931471:04crwdne2931471:0

crwdns2935297:06crwdne2935297:0

crwdns2917034:0crwdne2917034:0

how to fix the motherboard if booth leds stay lit when powering up?

ACIDGREEN TECHNO - crwdns2934203:0crwdne2934203:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 3

crwdns2936753:07crwdne2936753:0 8

crwdns2936753:030crwdne2936753:0 28

crwdns2942667:0crwdne2942667:0 3,452