Hamilton Beach 70740 Motor Replacement
crwdns2959932:0crwdnd2959932:0David Gedeoncrwdnd2959932:0crwdnd2959932:0crwdnd2959932:05crwdnd2959932:0crwdne2959932:0
crwdns2959936:0N'w 15, 2016crwdne2959936:0
crwdns2869540:0crwdne2869540:0: 896
crwdns2959988:0crwdne2959988:0
- crwdns2959990:0crwdne2959990:0
- 0
- crwdns2959992:0crwdne2959992:0
- 11
- crwdns2959994:0crwdne2959994:0
- 33
- crwdns2959996:0crwdne2959996:0
- 896
crwdns2955950:0crwdne2955950:0: 0
crwdns2959998:0crwdne2959998:0
crwdns2960000:0crwdne2960000:0crwdns2959984:0crwdne2959984:0: 2 3
crwdns2959974:02crwdne2959974:0
crwdns2959970:03crwdne2959970:0
crwdns2959986:0crwdne2959986:0: 0 1
crwdns2959958:0crwdne2959958:0
crwdns2959976:01crwdne2959976:0
crwdns2890100:0crwdne2890100:0
crwdns2944378:0crwdne2944378:0
crwdns2862605:0crwdne2862605:0
crwdns2862606:0crwdne2862606:0
crwdns2862611:0crwdne2862611:0
crwdns2862612:0crwdne2862612:0
crwdns2869444:0crwdne2869444:0
crwdns2869445:0crwdne2869445:0
crwdns2862633:0crwdne2862633:0
crwdns2862634:0crwdne2862634:0
crwdns2862635:0crwdne2862635:0
crwdns2862636:0crwdne2862636:0
crwdns2915892:0crwdne2915892:0
crwdns2959928:0crwdne2959928:0 ↓This guide is used to replace the motor.
crwdns2959930:0crwdne2959930:0
crwdns2943215:0crwdne2943215:0
-
Spudger4.9
-
-
-
-
-
Hold the food processor upside down and remove the two screws indicated with a screwdriver. Once unscrewed, remove the two rubber suction pads.
crwdns2952109:0crwdne2952109:0
-
-
-
Use a spudger to remove the 4 rubber base pads located at the corners of the device.
-
-
-
Unscrew all 4 screws that are located beneath the pads with a screwdriver and remove the plastic grey base.
-
-
-
Remove the screws indicated with a screw driver.
-
-
-
-
Remove the two screws behind the knob with a screwdriver.
-
-
-
-
-
Use a regular nylon spudger to remove the plastic caps at these locations with moderate pressure.
-
-
-
Remove the 4 screws located under the plastic caps with a screw driver.
-
-
-
Lift and remove the plastic gears at the center of the device.
-
Remove any grease residue underneath the plastic gears.
-
-
-
Remove the remaining screws to unhinge the motor located at the center of the device using a screw driver.
-
-
-
-
-
Remove to electrical cap to the positive terminal(black terminal), and undo the wiring.
-
-
-
Remove the electrical cap to the negative end(red wire), and undo the wiring. Once this is complete reconstruct the wiring with the new motor.
-
-
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:02crwdne2935229:0
crwdns2935287:0crwdne2935287:0
IUPUI, Team 1-1, Baechle Fall 2015 crwdns2935289:0IUPUI, Team 1-1, Baechle Fall 2015crwdne2935289:0
IUPUI-BAECHLE-F15S1G1
crwdns2931471:04crwdne2931471:0
crwdns2935297:072crwdne2935297:0
