crwdns2915892:0crwdne2915892:0
The guide will allow you to replace the speaker port inside your HTC Droid DNA.
crwdns2942213:0crwdne2942213:0
-
-
Poke a paperclip into the hole to the right of the SIM Card Tray. The SIM Card Tray will automatically pop out.
-
-
-
Pull out the SIM Card Tray with your fingers.
-
-
-
Starting at a corner, slowly work your way around the edge of the sides with your prying tool to loosen the front panel.
-
-
-
Slowly pull the panel apart from the back of the phone.
-
-
-
Set the device down so that the bottom of the phone is facing to the right.
-
Gently take off the piece of black tape surrounding the motherboard.
-
-
-
Use your tweezers to take off the yellow tape on the bottom left corner of the phone.
-
-
-
Rotate your phone 90 degrees clockwise so the bottom of the phone is facing you.
-
Use the T5 Torx screwdriver to remove the two 4mm screws located at the bottom of the phone.
-
-
-
Use the Phillips #000 screwdriver to remove the single 2.7mm void screw on the bottom right.
-
-
-
Rotate your phone back 90 Degrees counter-clockwise.
-
Use your tweezers to take off the small metal retaining bracket on the bottom right of the phone.
-
-
-
Remove the following Phillips #000 screws from the motherboard:
-
Four 1.6 mm screws
-
Two 1.5 mm screws
-
-
-
-
Use your pry tool to unfasten the connectors on both sides of the motherboard.
-
-
-
Use your tweezers to remove the two pieces of yellow tape shown.
-
-
-
Use your tweezers to gently snap up the white board on the bottom right of the motherboard.
-
-
-
Use your tweezers to disconnect the black connector on the bottom right of the motherboard.
-
-
-
Use your tweezers to gently snap the other white board on the bottom right of the motherboard up.
-
-
-
Use your tweezers to disconnect the other small connector on the bottom right of the motherboard.
-
-
-
Rotate the phone 180 degrees.
-
Use your tweezers to gently snap up the white board on the top left of the motherboard.
-
-
-
Use your tweezers to disconnect the cable on the top left of the motherboard.
-
-
-
Use your tweezers to gently snap up the black board on the top left of the motherboard.
-
-
-
Use your tweezers to gently remove the yellow connector on the top left of the phone.
-
-
-
Remove the long black wire on the left of the motherboard.
-
-
-
Reorient the phone so that the green camera board is farthest from you.
-
Use your tweezers to remove the two wires located at the top of the board. The wires snap off very easily so not much force is needed.
-
-
-
Use a Phillips #000 screwdriver to remove the two 3.9mm screws on top of motherboard.
-
-
-
Now, use your fingers to slowly pull up the motherboard and remove it from the phone.
-
-
-
Use the plastic prying tool to gently remove the charging port assembly.
-
-
-
Use a Phillips #000 screw driver to remove the single 2.1mm screw located on the backside of the assembly.
-
-
-
Use your tweezers to undo the red and black wire connection.
-
-
-
Use the plastic prying tool to separate the assembly into two pieces: blue and black.
-
-
-
Apply pressure to the grey side of the speaker with a blunt object to push out the speaker.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2915084:0crwdne2915084:0
Cal Poly, Team 4-43, Amido Fall 2014 crwdns2935289:0Cal Poly, Team 4-43, Amido Fall 2014crwdne2935289:0
CPSU-AMIDO-F14S4G43
crwdns2931471:04crwdne2931471:0
crwdns2935297:010crwdne2935297:0
