crwdns2942213:0crwdne2942213:0
-
-
Pull on the two tabs on the back of the printer to release the left side cover.
-
Remove the cover by rotating it towards the front of the printer.
-
-
-
With the printer turned so that the right side is facing upwards, use a metal spudger to disengage 3 tabs holding the right side cover in place.
-
Lift the cover off of the printer.
-
-
-
Remove 4 screws on the back of the printer.
-
Remove the back cover.
-
-
-
Remove 2 screws on the back of the printer, one on the left, and one on the front.
-
-
-
Disconnect the control panel cable and remove the top cover.
-
-
-
Disconnect the fan cable from the main board of the printer.
-
Remove the retaining clip holding the fan in.
-
Remove the 2 screws holding the fan in.
-
-
-
Remove the fan cable from the cable guide.
-
-
-
Disconnect one cable from the main board of the printer.
-
Disconnect the duplexer solenoid cable from the duplexer PCB.
-
Remove one screw on the duplexer PCB and remove the PCB from the printer.
-
-
-
Remove 3 screws holding the duplexer gears to the printer and remove the gears.
-
-
-
Remove one screw to remove the solenoid from the printer.
-
-
-
-
Pull on the two tabs on the back of the printer to release the left side cover.
-
Remove the cover by rotating it towards the front of the printer.
-
-
-
Remove 2 screws on the I/O port cover.
-
Remove 6 screws on the formatter.
-
Disconnect 3 connectors from the formatter.
-
Disconnect 2 flat flexible cables from the formatter.
-
Remove the formatter from the printer.
-
-
-
Remove the fuser gear by pushing in on the tab with a metal spudger.
-
-
-
Disconnect the cable to the tray connector and route it through the hole in the chassis.
-
-
-
Disconnect 2 cables from the main board and route them through the cable guide.
-
-
-
Remove the cable guide from the chassis.
-
-
-
Remove the cable guide from the other side of the chassis.
-
Disconnect 2 cables from the main board.
-
-
-
Use needle nose pliers to disconnect the high voltage wire from the fuser.
-
-
-
Remove the tray connector cable from the cable guide.
-
Disconnect the main motor cable.
-
-
-
Remove 3 screws from the right side of the printer.
-
Remove 3 screws from the left side of the printer.
-
The fuser assembly can now be removed from the printer.
-
-
-
Remove 4 screws from each side of the printer to remove the mainframe.
-
-
-
Remove 3 screws from the safety interlock assembly (one on top) and remove it from the printer.
-
-
-
Remove the feed plate from over the main board.
-
-
-
Remove the tray connector and motor cables from the cable guide.
-
-
-
Remove one screw from the cable guide and remove the cable guide from the chassis.
-
Remove one screw from the chassis.
-
-
-
Remove 2 screws from the left side of the chassis.
-
Push the formatter and safety interlock cables through the hole in the chassis.
-
-
-
Bend the chassis to allow the control board to come loose, and disconnect the 2 cables from the paper feed assembly.
-
Remove the main board from the printer.
-
-
-
Remove 4 screws on the control board to remove it from its metal plate.
-
-
-
Remove the cable guide from the chassis.
-
Remove 3 screws to remove the main motor.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2947410:01crwdne2947410:0
hp 1320 printer not running