crwdns2915892:0crwdne2915892:0
This Guide will walk you through replacing your keyboard on a HP 15-ac158dx Laptop. This is not an easy process, so you will want to pull out your plastic prying tools and Philips J00 Screw Driver and follow the instructions closely.
crwdns2942213:0crwdne2942213:0
-
-
Remove all external devices from the computer.
-
Remove the charging cord from the computer.
-
-
-
Turn off the computer by holding the power button.
-
-
-
To remove the battery, slide the left slider on the back to the unlocked position.
-
-
-
Push the right slider inwards.
-
Remove the battery out by pulling straight out and to the right.
-
-
-
Locate the CD Compartment panel and gently slide it out.
-
-
-
Remove the back of the laptop by unscrewing the screws shown.
-
Also remove the other 5 Phillips screws lining the back cover.
-
-
-
Using the prying tool, wedge it underneath the back of the laptop and do the same all around until the back comes off.
-
Dont forget to unscrew 2 screws under 2 plastic tabs (one on each hing). The lid will not come off without them being removed!
-
-
-
-
Locate the CD Compartment as shown and gently slide it out.
-
-
-
Locate the Fan as shown.
-
Pull out the black cable, with four wires attached from its port.
-
-
-
Pull out the white cable wire from its port.
-
Unscrew the two black Phillips screws holding in the fan.
-
-
-
Remove fan.
-
Unscrew the two screws holding in the fan.
-
-
-
Remove the TEN 3mm screws.
-
Remove the ONE 9mm screw.
-
-
-
Locate the four ribbon clips.
-
Lift the grey part of the ribbon clips.
-
Pull the ribbon cable out and repeat this step for all four ribbon cables.
-
Also use a spudger and release the TWO cables attaching the hard drive to the motherboard. Another ribbon cable is located where the fan was sitting.
-
-
-
Pull out the white cable (contains red and white cable attached to a black support) with wires from its port.
-
-
-
Lift up the cable port and place it to the side but do not remove completely from the laptop.
-
Remove the single Phillips screw securing it first.
-
-
-
Remove the VENDOR component.
-
Unscrew the single Phillips screw holding it to the frame first.
-
-
-
Using a plastic prying tools, remove the grey metal plate.
-
It will not come off easy, but do not force it off.
-
-
-
Locate the damaged keyboard and lift up with the prying tool to remove.
-
-
-
To put everything back together and use your laptop with the new keyboard, follow the steps in REVERSE..
-
ENJOY :)
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:05crwdne2935229:0
crwdns2915084:0crwdne2915084:0
Baylor, Team S1-G2, Johnson Spring 2018 crwdns2935289:0Baylor, Team S1-G2, Johnson Spring 2018crwdne2935289:0
BU-JOHNSON-S18S1G2
crwdns2931471:03crwdne2931471:0
crwdns2935297:06crwdne2935297:0
crwdns2944067:02crwdne2944067:0
Did you have to use soldering iron to melt the plastic rivets when putting back the keyboard?
Cheers.
I have done these before and yes, using a soldering iron to melt the plastic rivets is a good method.
