crwdns2915892:0crwdne2915892:0
To remove the lens assembly, you must remove some internal parts first. Some of these screws are in tight places, so they will be tedious to access.
crwdns2942213:0crwdne2942213:0
-
-
Pop up and pull back on the clip to remove the screen cover and expose the back panel with the touchscreen.
-
-
-
Use the metal spudger to pry around the perimeter of the panel.
-
Pry the panel upwards by inserting the metal spudger into the corner crease between the panel and camera shell.
-
-
-
Pry around the panel to ensure it is not attached to the device.
-
Move the panel to the side so you can access the internal components.
а где можно купить вот этот шлейф соединяющий дисплей и плату.???
Александр «ivkadre» Карпенко - crwdns2934203:0crwdne2934203:0
-
-
-
Peel back the rear panel ribbon cable that is adhered to the battery until it is completely separated from the battery.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Using tweezers, peel off the copper tape on the right side of the battery.
-
-
-
Place the plastic opening tool at one of the edges of the battery then pry until the battery is removed from the GoPro.
-
-
-
-
Use a pair of tweezers to disconnect the battery connector from the motherboard.
-
Gently pull the battery off the motherboard. Pulling vertically off the motherboard will give a clean release.
Lift the battery connector straight up.
hi what kind battery can replace for hero+?
-
-
-
Remove the two 6 mm Phillips #00 screws.
-
Remove the single 4 mm Phillips #000 screws.
-
-
-
Remove the image sensor from the camera.
-
-
crwdns2935267:0crwdne2935267:0Tweezers$4.99
-
Grab the edge of the ribbon cable with the tweezers and gently pull until the cable is disconnected from the motherboard.
-
-
-
Gently lift the microSD/Micro USB assembly up and out of the device.
-
-
-
Use your fingers and gently pull out the sensor from the motherboard by slowly and gradually pulling up on the image sensor box.
-
-
-
Remove the three 4 mm Phillips #000 screws securing the motherboard.
-
-
-
Use your fingers to gently remove the ribbon connected to the lens.
-
-
-
Use your fingers and carefully pull out the motherboard from under the lens. It may take a little bit of adjusting to get it out.
-
-
-
Remove the two 4 mm Phillips #000 screws securing the top button.
-
-
-
Remove the four 4 mm Phillips #000 screws securing the lens to the case.
-
-
-
Gently lift the lens up and out of the device.
-
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:02crwdne2935229:0
crwdns2915084:0crwdne2915084:0
USF Tampa, Team 2-4, Blackwell Fall 2015 crwdns2935289:0USF Tampa, Team 2-4, Blackwell Fall 2015crwdne2935289:0
USFT-BLACKWELL-F15S2G4
crwdns2931471:04crwdne2931471:0
crwdns2935297:020crwdne2935297:0
crwdns2947412:02crwdne2947412:0
I'm curious if you have any suggestions for sourcing the replacement part.
Bridgetown Electronics Repair - crwdns2934203:0crwdne2934203:0
My hing clip is broken, Can I remove the actual camera & replace the full waterproof case then reinstall my camera into the new replacement case ?
No parts required! What about the microSD/Micro USB assembly!!!! where to buy?!?!
WPN - crwdns2934203:0crwdne2934203:0