Garmin Fenix 3 Display Assembly Replacement
crwdns2959932:0crwdnd2959932:0Adam Estabrookcrwdnd2959932:0crwdnd2959932:0crwdnd2959932:02crwdnd2959932:0crwdne2959932:0
crwdns2959936:0Sun 1, 2019crwdne2959936:0
crwdns2869540:0crwdne2869540:0: 11K
crwdns2959988:0crwdne2959988:0
- crwdns2959990:0crwdne2959990:0
- 2
- crwdns2959992:0crwdne2959992:0
- 25
- crwdns2959994:0crwdne2959994:0
- 125
- crwdns2959996:0crwdne2959996:0
- 11,332
crwdns2955950:0crwdne2955950:0: 5
crwdns2960002:01crwdne2960002:0, crwdns2960008:04crwdne2960008:0
crwdns2960000:0crwdne2960000:0crwdns2959984:0crwdne2959984:0: 8 9
crwdns2959974:08crwdne2959974:0
crwdns2959970:09crwdne2959970:0
crwdns2959986:0crwdne2959986:0: 0 1
crwdns2959958:0crwdne2959958:0
crwdns2959976:01crwdne2959976:0
crwdns2862591:0crwdne2862591:0
crwdns2862592:0crwdne2862592:0
crwdns2915892:0crwdne2915892:0
crwdns2959928:0crwdne2959928:0 ↓If your watch face is damaged, cracked, or chipped, you can learn how to replace it using this guide. This guide involves simply unscrewing screws from the watch face and carefully disconnecting the screen’s ribbon cable from the motherboard. You will need a T6 Torx screwdriver and a spudger.
crwdns2959930:0crwdne2959930:0
crwdns2943215:0crwdne2943215:0
-
-
Spudger4.9
-
-
-
Use a T6 screwdriver to remove the five 1.7 mm screws from the watch face.
crwdns2952109:0crwdne2952109:0
-
-
-
Carefully lift the face off the watch base.
-
-
-
Use a spudger to lift up and free the screen ribbon cable's press-fit connector from the motherboard.
-
-
-
-
Set the watch face aside.
-
-
To reassemble your device, follow these instructions in reverse order.
crwdns2935221:0crwdne2935221:0
crwdns2935229:08crwdne2935229:0
crwdns2935287:0crwdne2935287:0
Appalachian State University, Team S1-G3, Menagarishvili Fall 2018 crwdns2935289:0Appalachian State University, Team S1-G3, Menagarishvili Fall 2018crwdne2935289:0
APSU-MENAGARISHVILI-F18S1G3
crwdns2931471:03crwdne2931471:0
crwdns2935297:060crwdne2935297:0
crwdns2947412:04crwdne2947412:0
Thanks Adam. How do you chgange the glass in a Fenix 3? I can strip the watch down as you have described but not sure how to replace the screen.
Richard Davies-Cooke - crwdns2934203:0crwdne2934203:0 crwdns2950251:0crwdne2950251:0
I have the same question.
Nicolas Chartier - crwdns2934203:0crwdne2934203:0 crwdns2950251:0crwdne2950251:0
How do you make sure ribbon connector is aligned correctly
Steven - crwdns2934203:0crwdne2934203:0 crwdns2950251:0crwdne2950251:0
I have Fennix3, replaced the battery with new one (tested the battery before fixing), however, after complete assembly the watch does not start up? any hints?
Abdullah - crwdns2934203:0crwdne2934203:0 crwdns2950251:0crwdne2950251:0
