crwdns2933423:0crwdne2933423:0
crwdns2947577:0crwdnd2947577:0crwdne2947577:0
GE A1050 LCD Replacement

GE A1050 LCD Replacement

oldturkey03

crwdns2944107:0crwdnd2944107:0oldturkey03crwdnd2944107:0crwdnd2944107:0crwdnd2944107:04crwdnd2944107:0crwdne2944107:0

crwdns2944111:0Mud 2, 2017crwdne2944111:0

15 - 30 crwdns2931279:0crwdne2931279:0
crwdns2937801:0crwdne2937801:0
crwdns2944444:0crwdne2944444:0

crwdns2915892:0crwdne2915892:0

crwdns2942287:0crwdne2942287:0

The repair of the LCD is straight forward. No special skills or knowledge are required.

crwdns2942213:0crwdne2942213:0

crwdns2943213:0crwdne2943213:0

crwdns2943215:0crwdne2943215:0

  1. GE A1050 LCD Replacement, LCD: crwdns2935265:01crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement, LCD: crwdns2935265:01crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement, LCD: crwdns2935265:01crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Remove the batteries, hand strap, and memory card if so equipped.

    • Remove the two Phillips screws from the bottom.

    • Remove the two Phillips screws from the left side.

  2. GE A1050 LCD Replacement: crwdns2935265:02crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement: crwdns2935265:02crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement: crwdns2935265:02crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Remove the two screws from the right side.

    • The two screws from the left side are shorter than the ones from the right. Keep those separated.

    • Start splitting the case from the battery compartment to the sides. No special tool is needed to split the case.

  3. GE A1050 LCD Replacement: crwdns2935265:03crwdnd2935265:01crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement: crwdns2935265:03crwdnd2935265:02crwdnd2935265:03crwdne2935265:0 GE A1050 LCD Replacement: crwdns2935265:03crwdnd2935265:03crwdnd2935265:03crwdne2935265:0
    • Do not remove the back side of the case, just flip it over. The speaker is connected by wires to the main body, but positioned in the back case.

    • Flip the LCD to the bottom. You can not yet remove it, because it is still attached to the board.

    • The LCD cable is held into the connector via some compression clips. Move both ends carefully away from the connector, toward the LCD.

    • The clips only move about an 1/8 of an inch. Be careful not to use too much force.

  4. GE A1050 LCD Replacement: crwdns2935265:04crwdnd2935265:01crwdnd2935265:01crwdne2935265:0
    • After exchanging the LCD for a new one, and after reassembling your camera, you should have a working LCD.

crwdns2915888:0crwdne2915888:0

To reassemble your device, follow these instructions in reverse order.

crwdns2935227:0crwdne2935227:0

crwdns2947821:0crwdne2947821:0

crwdns2947823:0crwdne2947823:0

oldturkey03

crwdns2935283:009/29/10crwdne2935283:0

826,387 crwdns2915208:0crwdne2915208:0

crwdns2935297:0122crwdne2935297:0

crwdns2947412:00crwdne2947412:0

crwdns2917038:0crwdne2917038:0

crwdns2936625:0crwdne2936625:0:

crwdns2936751:024crwdne2936751:0 2

crwdns2936753:07crwdne2936753:0 9

crwdns2936753:030crwdne2936753:0 28

crwdns2942667:0crwdne2942667:0 2,047