Furbo Dog Camera Camera Lens Replacement
crwdns2959934:0crwdnd2959934:0Piper Strgarcrwdnd2959934:0crwdnd2959934:0crwdnd2959934:0crwdne2959934:0
crwdns2959936:0Mud 16, 2022crwdne2959936:0
crwdns2869540:0crwdne2869540:0: 826
crwdns2959988:0crwdne2959988:0
- crwdns2959990:0crwdne2959990:0
- 3
- crwdns2959992:0crwdne2959992:0
- 19
- crwdns2959994:0crwdne2959994:0
- 71
- crwdns2959996:0crwdne2959996:0
- 826
crwdns2955950:0crwdne2955950:0: 1
crwdns2960002:01crwdne2960002:0.
crwdns2959984:0crwdne2959984:0: 0 1
crwdns2959956:0crwdne2959956:0
crwdns2959968:01crwdne2959968:0
crwdns2959986:0crwdne2959986:0: 0 1
crwdns2959958:0crwdne2959958:0
crwdns2959976:01crwdne2959976:0
crwdns2890100:0crwdne2890100:0
crwdns2944378:0crwdne2944378:0
crwdns2915892:0crwdne2915892:0
crwdns2959928:0crwdne2959928:0 ↓This guide shows how to replace the camera lens of the Furbo Dog camera (Model:2). Be sure that you are working on the Camera and not the other components that are very close to it!
crwdns2959930:0crwdne2959930:0
crwdns2943213:0crwdne2943213:0
crwdns2943215:0crwdne2943215:0
-
-
-
Remove the lid from the top of your Furbo Dog Camera.
crwdns2952109:0crwdne2952109:0
-
-
-
Rotate your Furbo so that the bottom faces you.
-
Remove the rubber caps to reveal the four screws on the bottom of the Furbo.
-
-
crwdns2935267:0crwdne2935267:0Flathead 3/32" or 2.5 mm Screwdriver$5.49
-
Use a 2.5 mm Flathead screwdriver to remove the four 5 mm screws from the bottom of the Furbo.
-
Use a 2.5 mm Flathead screwdriver to remove the single 5 mm screw under the silver sticker.
-
-
-
Rotate your Furbo so that the side is facing towards you.
-
Use an opening tool to separate the two plastic coverings.
-
-
-
Once you have separated the two plastic coverings, remove one side by pulling on it and carefully separating it from the adhesive.
-
-
-
-
-
Carefully remove the copper foiling that surrounds the camera hardware.
-
-
-
Use a Phillips #000 screwdriver to remove the 2.5 mm screws at the top of the camera hardware.
-
-
-
Gently pry the metal backing off of the camera hardware.
-
-
-
-
Use a Phillips #000 screwdriver to remove the 0.4 mm screws that attach the camera to the Furbo case.
-
-
-
Gently pry the camera off and detach it from the Furbo.
-
-
-
Detach the wire attaching the camera hardware from the Furbo.
-
-
-
Once removed, you may replace your camera.
-
-
To reassemble your device, follow these instructions in reverse order.
crwdns2935287:0crwdne2935287:0
University of Alabama, Team 1-1, Bedsole Spring 2022 crwdns2935289:0University of Alabama, Team 1-1, Bedsole Spring 2022crwdne2935289:0
UA-BEDSOLE-S22S1G1
crwdns2931471:03crwdne2931471:0
crwdns2935297:072crwdne2935297:0
